ICOM IC-F3063S 用户手册

 

FM deviation meter

Frequency range 
Measuring range 

: DC–300 MHz
: 0 to 

±10 kHz    

Attenuator

Power attenuation 
Capacity 

: 20 or 30 dB
: 10 W

Frequency counter

Frequency range
Frequency accuracy 
Sensitivity 

: 0.1–300 MHz
: ±1 ppm or better 
: 100 mV or better

Standard signal 
generator (SSG)

Frequency range 
Output level   

: 0.1–300 MHz
:  0.1 µV to 32 mV

(–127 to –17 dBm) 

RF power meter

Measuring range   
Frequency range  
Impedance     
SWR 

: 1–10 W
: 100–300 MHz
: 50 

Ω

: Better than 1.2 : 1

Oscilloscope

Frequency rang  
Measuring range 

: DC–20 MHz
: 0.01–20 V 

External speaker

Input impedance 
Capacity 

: 8 

Ω

: 1 W or more

6 - 1

When adjusting IC-F3060 series, the optional CS-F3060 ADJ 

ADJUSTMENT SOFTWARE

 (Rev. 1.1 or later), OPC-966 

JIG CABLE

 

(modifi ed OPC-966 

CLONING CABLE

; see illustration page 5-2) and below test equipments are required.

▄ SYSTEM REQUIREMENTS

• Microsoft

®

 Windows

®

 98/98SE/Me/2000/XP

• RS-232C serial port (D-sub 9 pin)

q Quit all applications when Windows is running.

w

 Insert the CD into the appropriate CD drive.

e

  Double-click the “Setup.exe” contained in the ‘CS-F3060 

ADJ’ folder in the CD drive.

r

  The “Welcome to the InstallShield Wizard for CS-F3060 

ADJ” will appear. Click [Next>].

t

  The “Choose Destination Location” will appear. Then click 

[Next>] to install the software to the destination folder. (e.g. 
C:\Program Files\Icom\CS-F3060 ADJ)

y

 

 

After the installation is completed, the “InstallShield Wiz-
ard Complete” will appear. Then click [Finish].

u

 Eject the CD.

i

  Program group ‘CS-F3060 ADJ’ appears in the ‘Programs’ 

folder of the start menu, and ‘CS-F3060 ADJ’ icon ap-
pears on the desk top screen.

Clone the adjustment frequencies into the transceiver, and
set the confi guration using with the CS-F3060 

CLONING SOFT-

WARE

 before starting the software adjustment. Otherwise, the 

software adjustment can not be started. 

CAUTION!:  BACK UP the originally programmed mem-

ory data in the transceiver before program-
ming the adjustment frequencies.  
When program the adjustment frequencies into 
the transceiver, the transceiver’s memory data 
will be overwritten and lose original memory 
data at the same time.

Microsoft and Windows are registered trademarks of Micro-
soft Corporation in the U.S.A. and other countries.

▄  STARTING SOFTWARE ADJUSTMENT

q  Connect the transceiver and PC with OPC-966 

JIG CABLE

.

w Turn the transceiver power ON.

e  Boot up Windows, and click the program group ‘CS-F3060 

ADJ’ in the ‘Programs’ folder of the [Start] menu, then 
CS-F3060 series ADJ’s window appears.

r  Click ‘Connect’ on the CS-F3060 ADJ’s window, then 

appears transceiver’s up-to-date condition.

t  Set or modify adjustment data as specifi ed.

1

174.000 MHz

TX power
Mode

: Low1
: Narrow

2

154.900 MHz

TX power
Mode

: Low1
: Narrow

3

155.000 MHz

TX power
Mode

: High
: Wide

4

155.000 MHz

TX power
Mode

: Low2
: Wide

5

155.000 MHz

TX power
Mode

: Low1
: Wide

6

136.000 MHz

TX power
Mode

: Low1
: Wide

7

174.000 MHz

TX power
Mode

: Low1
: Wide

8

136.000 MHz

TX power
Mode

: Low1
: Narrow

9*

155.000 MHz

TX power
Mode

: Low1
: Digital

10*

136.000 MHz

TX power
Mode

: Low1
: Digital

11*

174.000 MHz

TX power
Mode

: Low1
: Digital

12

155.000 MHz

TX power
Mode
CTCSS

: Low1
: Wide
: 151.4 Hz

13

155.000 MHz

TX power
Mode

: Low1
: Narrow

14

†

155.000 MHz

TX power
Mode

: Low1
: Middle

15

†

136.000 MHz

TX power
Mode

: Low1
: Middle

16

†

174.000 MHz

TX power
Mode

: Low1
: Middle

*; Necessary only when the optional UT-119 is installed.

†

; [EUR-01] only