Garmin 190-01166-02 用户手册

下载
页码 48
9
GHP 10 Marine Autopilot System Installation Instructions
Category
Setting
Description
Tachometer Setup
Verify Tachometer
With the engine (or engines) running, compare the RPM readings on the 
GHC 10 with the tachometer on the dashboard of your boat. Adjust the 
Pulses Per Rev 
with the arrows if the values do not match, and then 
select 
Done
. When you adjust the 
Pulses Per Rev 
with the arrows, there 
is a delay before the new RPM readings appear on the GHC 10. For each 
adjustment, be sure to wait until the GHC 10 adjusts to the new reading. 
Tachometer Setup
RPM Source
Select the engine (or engines) to which you wired the tachometer sensor 
from the CCU. If you connected a NMEA 2000-compatible engine to the 
NMEA 2000 network, select 
nMEA 2000
. For a single-engine boat, select 
port.
Tachometer Setup
Planing RPM
Take note of the RPM reading from the tachometer on the dashboard of 
your boat at the point your boat transitions from displacement to planing 
speed. If the value does not match the value on the GHC 10, use the 
arrows to adjust the value.
Tachometer Setup
Low RPM Limit
Take note of the RPM reading from the tachometer on the dashboard of 
your boat at the lowest RPM point. If the value does not match the value 
on the GHC 10, use the arrows to adjust the value.
Tachometer Setup
High RPM Limit
Take note of the RPM reading from the tachometer on the dashboard of 
your boat at the highest RPM point. If the value does not match the value 
on the GHC 10, use the arrows to adjust the value.
Hydraulic Setup
Helm Displacement
The helm displacement is usually written on the body of the helm pump. 
If you are unsure, consult the manufacturer of your boat for the helm 
displacement value. Use the arrows on the GHC 10 to enter the helm 
displacement value.
Hydraulic Setup
Lock to Lock Turns
Count the number of turns it takes your helm to go from lock to lock (fully 
turned port to fully turned starboard). Use the arrows on the GHC 10 to 
enter the value you counted.
Hydraulic Setup
Verify Steering Direction
Use the arrows on the GHC 10 to test the steering direction. When you 
push the right arrow, the motor should turn the boat to the right, and vice 
versa. Determine if the engines are steering in the correct direction and 
press 
Continue
. Use the GHC 10 to answer the questions.
Hydraulic Setup
Linkage Compensation
Adjust the linkage compensation if the steering is loose or sloppy. The 
higher you set this value, the more the autopilot compensates for loose or 
sloppy steering. Use this setting with caution.
Turn Fine Tuning Setup > Rudder Gains
Low Speed
Set the rudder gain for low speeds.
Turn Fine Tuning Setup > Rudder Gains
Low Speed Counter
Set the rudder gain counter-correction for low speeds.
Turn Fine Tuning Setup > Rudder Gains
High Speed
Set the rudder gain for high speeds.
Turn Fine Tuning Setup > Rudder Gains
High Speed Counter
Set the rudder gain counter-correction for high speeds.
Turn Fine Tuning Setup
Acceleration Limiter
Limit the aggressiveness of autopilot-controlled turns. Increase the 
percentage to limit the turn rate, and decrease the percentage to allow 
higher turn rates.
Navigation Setup
Fine Heading Adjustment Increase or decrease to fine-tune the autopilot heading.
Navigation Setup > NMEA Setup
NMEA Checksum
If the connected GPS unit incorrectly calculates checksums, you may 
still be able to use it if you turn this setting off. When off, data integrity is 
compromised.
Navigation Setup > NMEA Setup
Reversed XTE
If the connected GPS unit sends the incorrect steering direction with the 
cross track error signal, use this setting to correct the steering direction.
Navigation Setup
Navigation Gain
Because the cross track error data transmitted by a NMEA 0183 GPS 
device is only accurate within .01 mile (60 ft.), the gain may need 
adjustment. Increase this setting until the boat oscillates back and forth 
near the course line, then lower it a few levels.
Navigation Setup
Navigation Trim Gain
After adjusting the Navigation gain, increase this setting until you can see 
the standoff from the course line decreasing over time.
note: Certain configuration settings are available when using the GHC 10 normally, such as enabling and disabling the Shadow 
Drive, adjusting the sensitivity of the Shadow Drive, and adjusting the Sea State Filtering setting. See the configuration section of the 
GHP 10/GHC 10 Quick Start Manual for more information.