Kenmore 90109 用户手册
3. Be sure all gas connections are securely
tightened.
4. Turn on gas supply.
5. Open the grill main lid.
6. Push and turn any main burner control knob to
5. Open the grill main lid.
6. Push and turn any main burner control knob to
HI position. Push Electronic Ignition button for
3 to 5 seconds to light burner.
3 to 5 seconds to light burner.
7. If the burner does not light after 5 seconds, turn
knob to OFF. Turn gas OFF at LP tank and wait
5 minutes for gas to clear. Then turn gas ON at
tank and repeat step 5
5 minutes for gas to clear. Then turn gas ON at
tank and repeat step 5
8. If burner still does not light, see Match Lighting
section and If Grill Still Fails to Light section on
following page.
following page.
9. To light additional burners, turn burner knob(s)
to HI . Push and hold electronic ignition button
to light burner. Adjust knob(s) to desired setting.
to light burner. Adjust knob(s) to desired setting.
1. Make a 50/50 (soap/water) mild soap solution.
2. Turn the control knobs to full OFF position; then turn
2. Turn the control knobs to full OFF position; then turn
gas ON at supply tank.
3. Apply the soap solution with a clean brush to all gas
connections. See below. If growing bubbles appear
in the solution the connections are not properly
sealed. Check each fitting and tighten or repair as
necessary.
in the solution the connections are not properly
sealed. Check each fitting and tighten or repair as
necessary.
4. If you have a gas connection leak you cannot repair,
turn gas OFF at supply tank, disconnect fuel line
from your grill and call 1-800-913-8999 (English) or
1-800-648-5864 (French) or your gas supplier for
repair assistance.
from your grill and call 1-800-913-8999 (English) or
1-800-648-5864 (French) or your gas supplier for
repair assistance.
5. Also apply soapy solution to the tank seams. See
below. If growing bubbles appear, shut tank OFF
and do not use or move it! Contact an LP gas
supplier or your fire department for assistance.
and do not use or move it! Contact an LP gas
supplier or your fire department for assistance.
Grill Lighting Instructions for Main Burners
1. Do not smoke while lighting grill or checking gas
1. Do not smoke while lighting grill or checking gas
supply connections.
2. Be sure that LP gas tank is sufficiently full.
WARNING
Failure to open grill lid during the lighting
procedure could result in a fire or explosion
that could cause serious bodily injury, death,
or property damage.
procedure could result in a fire or explosion
that could cause serious bodily injury, death,
or property damage.
!
16
USING THE SIDE BURNER:
Inspect the gas supply hose prior to turning the gas
“ON”. If there is evidence of cuts, wear or abrasion,
it must be replaced prior to use. Do not use the
side burner if the odor of gas is present.
WARNING: Always keep your face and body as
far away from the burner as possible when
lighting.
Inspect the gas supply hose prior to turning the gas
“ON”. If there is evidence of cuts, wear or abrasion,
it must be replaced prior to use. Do not use the
side burner if the odor of gas is present.
WARNING: Always keep your face and body as
far away from the burner as possible when
lighting.
Gas Connection Leak Check
Gas Tank Leak Check
Checking for LP gas leaks
Never test for leaks with a flame. Prior to first use, at
the beginning of each season, or every time your LP
gas tank is changed, you must check for gas leaks.
the beginning of each season, or every time your LP
gas tank is changed, you must check for gas leaks.
Grill Lighting Instruction
LIGHTING INSTRUCTIONS FOR SIDE BURNER
1. Open side burner lid fully.
2. Push and turn side burner knob to HI position.
2. Push and turn side burner knob to HI position.
Push and hold Electronic Ignition button for 3-5
seconds to light burner.
seconds to light burner.
3. If the side burner does not light after 5 seconds,
turn knob to OFF. Turn gas OFF at LP tank and
wait 5 minutes for gas to clear. Then turn gas
ON at tank and repeat step 2.
wait 5 minutes for gas to clear. Then turn gas
ON at tank and repeat step 2.
4. If burner still does not light, see Match Lighting
section and If Grill Still Fails to Light Section on
following page.
following page.