Napoleon Grills BIZC600 用户手册
ZERO CLEARANCE INSULATING LINER
INSTRUCTION GUIDE
This liner is designed for use in a combustible enclosure; the liner must be supported from the bottom by a ledge on either side or a full deck
beneath the liner (refer to opening diagram). Please use this manual in conjunction with your main manual to properly assemble your built
in grill.
beneath the liner (refer to opening diagram). Please use this manual in conjunction with your main manual to properly assemble your built
in grill.
KIT CONTENTS
BOTTOM PANEL
1PC
SIDE PANELS
2PCS
REAR PANEL
1PC
#8 x ½” TEK SCREWS
15PCS
#14 x ½” HEX HEAD SCREWS
6PCS
The installation must be performed by a licensed gas fitter, and all connections must be leak
tested before operating the grill.
tested before operating the grill.
N415-0152 NOV21/06
BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be
located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe,
copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane
installation code in Canada, or to the National Fuel Gas code, ANSI Z223.1 in the United States. The minimum recommended
piping size is NPS 1/2" for rigid pipe, and 1/2" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes
to conform with CAN B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States. The gas supply must be connected to the 3/8” flare elbow fitting located under the right hand side of the control
panel. If installing a side burner, a separate line must be branched off to the side burner unit and enter the side burner opening
at the specified location. If the enclosure is to house a propane cylinder, the tank portion of the enclosure must be ventilated
according to local codes, and must not have communication with the cavity used to enclose the gas grill. The tank can not be
stored below the gas grill.
located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe,
copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane
installation code in Canada, or to the National Fuel Gas code, ANSI Z223.1 in the United States. The minimum recommended
piping size is NPS 1/2" for rigid pipe, and 1/2" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes
to conform with CAN B149.1. Propane Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States. The gas supply must be connected to the 3/8” flare elbow fitting located under the right hand side of the control
panel. If installing a side burner, a separate line must be branched off to the side burner unit and enter the side burner opening
at the specified location. If the enclosure is to house a propane cylinder, the tank portion of the enclosure must be ventilated
according to local codes, and must not have communication with the cavity used to enclose the gas grill. The tank can not be
stored below the gas grill.
BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and piping should be
located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe,
copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane
Installation Code in Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended
piping size is NPS 1/2" for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes
to conform with CAN B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States.
located as shown in the built-in instructions. Do not use hose to connect the unit. It must be connected with either rigid pipe,
copper tube or an approved flexible metal connector. The installation must comply with CAN B149.1 Natural Gas and Propane
Installation Code in Canada, or to the National Fuel Gas Code, ANSI Z223.1 in the United States. The minimum recommended
piping size is NPS 1/2" for rigid pipe, and 5/8" OD for copper tubing (based on a 20 ft run). Longer runs may require larger sizes
to conform with CAN B149.1. Natural Gas Installation Code in Canada or to the National Fuel Gas Code, ANSI Z223.1 in the
United States.
Built in units are supplied with a drip pan which holds only a minimal amount of grease. To prevent grease fires, the pan
must be cleaned after each use.
must be cleaned after each use.
H
G A S
INLET
OPENING
INLET
OPENING
6.500”
W
D
2”MIN
34” RECOMMENDED
BIZC450
35.875”
22.937”
11.125”
BIZC600
44.125”
22.937”
11.125”
Model
Dimensions
W
D
H
2.000”