Baby Trend 8207BCC 用户手册
CONTENTS (Fig. 1-1):
1 Playard
1 Mattress
1 Organizer
2 Leg extensions (1 Left,1 Right)
2 Leg extensions (1 Left, 1 Right) with Wheels,
1 Mattress
1 Organizer
2 Leg extensions (1 Left,1 Right)
2 Leg extensions (1 Left, 1 Right) with Wheels,
and hardware
1 Travel or Storage bag
BEFORE YOU BEGIN:
The Baby Trend Playard is designed so that,
when properly setup, the fabric of the playard places pressure on the 4
top rails making them nearly impossible to unlock. This safety feature
is activated when you push down on the playard floor to lock the bottom
rails. When setting up the playard, if you allow the bottom rails to lock
before locking the top rails, the fabric pressure will not allow you to lock
the top rails. Please see (Fig. 7.) for the proper position of the bottom of the
playard when locking the top rails. Always keep fingers away from corners
when setting playard up.
top rails making them nearly impossible to unlock. This safety feature
is activated when you push down on the playard floor to lock the bottom
rails. When setting up the playard, if you allow the bottom rails to lock
before locking the top rails, the fabric pressure will not allow you to lock
the top rails. Please see (Fig. 7.) for the proper position of the bottom of the
playard when locking the top rails. Always keep fingers away from corners
when setting playard up.
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 Velcro straps
and set mattress aside (Fig. 2).
2. Turn the playard upside down. (Fig. 3). Push each leg extension into the
bottom of the leg until both sides of extension snap into place. (Fig. 4).
Check that the extension is firmly connected. Attach the wheels to the
playard with the axle and nut as shown in figure (Fig. 5). The brake cluster
on the wheel must face to the inside. The axle is inserted from the outside
to the inside. (Fig. 6). Check that the wheels are firmly connected.
Check that the extension is firmly connected. Attach the wheels to the
playard with the axle and nut as shown in figure (Fig. 5). The brake cluster
on the wheel must face to the inside. The axle is inserted from the outside
to the inside. (Fig. 6). Check that the wheels are firmly connected.
3.
Stand Playard on legs keeping feet of playard close together as shown in
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.
* READ IMPORTANT: In order to continue, the handle in the center
of the floor of the Playard MUST remain raised in order for the
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard
should almost touch each other. All 4 bottom rails must be pointed
upward in order to LOCK top rails.
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard
should almost touch each other. All 4 bottom rails must be pointed
upward in order to LOCK top rails.
4. Push down on center of Playard floor until it is flat and locks into
position (Fig. 8). The center lock mechanism will lock automatically.
The center lock will rotate clockwise about 90 degrees as it locks.
The center lock will rotate clockwise about 90 degrees as it locks.
NOTE: Test rails to make sure they are locked. Push down on each
rail making sure they are rigid and in a set position.
rail making sure they are rigid and in a set position.
Figure 1-1.
Figure 2.
Figure 3
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA
TO ASSEMBLE PLAYARD
Figure 1.
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
3
Leg extensions
Wheels