Baby Trend 1304TW 用户手册

Installation Instructions for Peg Perego

Primo Viaggio

The Double Snap-N-Go

will accommodate the Peg Perego

Primo Viaggio

Infant Car Seat. Please follow these instructions for proper installation of the

Primo Viaggio

Front Seat:

1. Remove (unscrew) Crossbars A1, B1, and D from the Double Snap-N-Go

frame. Remove the Car Seat Straps from the Double Snap-N-Go

frame.

Retain the screws you remove.

2. Attach Crossbar A1 to the Double Snap-N-Go

frame using the two holes

labeled #4. Use the two screws that you removed in step 1. Please see

figure 1.

3. Attach both Car Seat Straps to the Double Snap-N-Go

frame using the two

holes labeled #3. Use the two screws that you removed in step 1. Please

see figure 1.

Rear Seat:

1. Remove (unscrew) Crossbars A2, B2, and B1 from the Double Snap-N-

frame. Remove the Car Seat Straps from the Double Snap-N-Go

frame. Retain the screws you remove.

2. Attach Crossbar A2 to the Double Snap-N-Go

frame using the two holes

labeled #3. Use the two screws that you removed in step 1. Please see

figure 2.

3. Attach Crossbar B1, so that the bent section faces down, to the Double

Snap-N-Go

frame using the two holes labeled #4. Use the two screws that

you removed in step 1. Please see figure 2

4. Attach both Car Seat Straps to the Double Snap-N-Go

frame using the two

holes labeled #2. Use the two screws that you removed in step 1. Please

see figure 2.

Insertion of the Peg Perego

Primo Viaggio

Infant Car Seat:

1. With one hand grasp the car seat handle (in its upright, carrying position)

and with your other hand squeeze the handle on the back of the car seat

(see step 8, to remove car seat, of the Primo Viaggo instructions) and gently

place the seat, so that the baby faces the rear, onto the Double Snap-N-Go

so that the rear small grooves on the seat bottom hook over Crossbar C for

the front or Crossbar B1 for the rear. Release the handle and check that the

seat locked onto the bar. See Figure 3.

FOR SAFE OPERATION, IT IS

VERY IMPORTANT THAT THE REAR LATCHES OF THE SEAT

LOCK SECURELY ONTO THE CROSSBAR.

2. Feed the Car Seat Straps through the two slots found on the rear of the Peg

Perego

Primo Viaggio

Car Seat shell as shown in figure 4. Buckle the

two straps together. The first time your do this, you will need to adjust the

length of the strap for a tight fit around the car seat. Please see figure 4.

3. Test for secure installation by moving the car seat in all directions. The car

seat should be securely attached to the Double Snap-N-Go

Removal of the Peg Perego

Primo Viaggio Infant Car Seat

1. Unlock the Car Seat Strap and remove.

2. With one hand, grasp the car seat handle (in its upright, carrying position)

and with your other hand squeeze the handle on the back of the car seat (see

step 8, to remove car seat, of the Primo Viaggo

instructions) and lift the car

seat upward from the Double Snap-N-Go

. See Figure 5.

Bar A1

Hole #5

Hole #4

Hole #3

Strap

Bar C

Bar A2

Bar B1
down

Hole #3

Hole #2

Strap

Hole #4

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Peg Perego

and Primo Viaggio

are the trademarks of their owners. They

are not associated with Baby Trend and no approval or endorsement is implied.