Maytag 8101P641-60 用户手册
STEP 5: Install The Mounting Plate
15
Center Line
A
C
B
Draw
Center Line
Draw Lines
on Studs
on Studs
For Wall-
Vented Only
Minimum 66
"
From the Floor
Support Tab
Support Tab
E
Mounting
Plate
D
3/16 Hole on Studs
5/8 Hole on Dry wall Only
3/16 Hole on Studs
5/8 Hole on Dry wall Only
Center Line
Draw
Center Line
Draw Lines
on Studs
on Studs
For Wall-
Vented Only
Minimum 66
"
From the Floor
Support Tab
Support Tab
E
Mounting
Plate
C
D
A
B
(1 piece mounting plate)
(3 pieces mounting plate)
The Oven Must Be Connected To At Least One
Wall Stud.
1. Draw a vertical line on the wall at the center of the 30 wide
space. Use the mounting plate as the template for the rear
wall. Place the mounting plate on the wall, making sure
that the tabs are against the bottom of the cabinet. Line up
the notch and center line on the mounting plate to the
center line on the wall.
wall. Place the mounting plate on the wall, making sure
that the tabs are against the bottom of the cabinet. Line up
the notch and center line on the mounting plate to the
center line on the wall.
2. While holding the mounting plate with one hand, draw
circles on the wall at holes A, B, C and D. Four holes must
be used for mounting. If the holes are not used, the
installation will not be secure. Installer must use these
holes for proper installation. Use toggle bolts through these
holes unless one of them lines up with a stud. Use a wood
screw for studs.
be used for mounting. If the holes are not used, the
installation will not be secure. Installer must use these
holes for proper installation. Use toggle bolts through these
holes unless one of them lines up with a stud. Use a wood
screw for studs.
NOTE: Draw a fifth circle inside area E, through one of the
bottom holes to match the location of a stud. For wall-
vented: The oven requires a rear wall cutout opening
for the rear wall duct and the exhaust adaptor must
be attached to the mounting plate. See the next page
on how to prepare the rear wall cutout opening and
the exhaust adaptor/mounting plate for wall-vented.
vented: The oven requires a rear wall cutout opening
for the rear wall duct and the exhaust adaptor must
be attached to the mounting plate. See the next page
on how to prepare the rear wall cutout opening and
the exhaust adaptor/mounting plate for wall-vented.
3. Drill holes on the circles. If there is a stud, drill a 3/16 hole
for lag screws. If there is no stud, drill a 5/8 hole for toggle
bolts. Make sure to use at least 1 lag screw in a stud, and
4 toggle bolts in the drywall or the plaster.
bolts. Make sure to use at least 1 lag screw in a stud, and
4 toggle bolts in the drywall or the plaster.
4. Attach the plate to the wall. To use spring toggle head
bolts: Remove the toggle wings from the bolts. Insert the
bolts into the mounting plate and replace the spring toggle
head to 3/4 past the bolt ends. Insert the spring toggle
head into the holes in the wall to mount the plate. You may
pull forward on the plate to help in tightening the toggle
bolts. Tighten all bolts.
bolts into the mounting plate and replace the spring toggle
head to 3/4 past the bolt ends. Insert the spring toggle
head into the holes in the wall to mount the plate. You may
pull forward on the plate to help in tightening the toggle
bolts. Tighten all bolts.
Figure 28
Figure 27
Wall
Mounting
Plate
Space More Than Wall Thickness
Bolt
End
End
Toggle Bolt
Toggle Wings