Shark SV726N 用户手册

1. Remove the vacuum cleaner from 

the charging base

2. To start the unit, push the "On/Off" 

switch to the "On" position.

3. To stop the vacuum cleaner, slide 

the "On/Off" switch to the "Off" 

position.

4. A crevice tool is provided for 

cleaning narrow, hard to reach 

places. A dusting brush is provided 

for cleaning upholstery, furniture, 

etc.

Model SV726N Cordless Vacuum is 

powered by Nickel-Cadmium Ni-Cd) 

batteries, which must be recycled or 

disposed of properly in accordance 

with state, federal and local laws.
If uncertain as to how to remove the 

battery pack, we suggest you take your 

hand vacuum to a reputable small 

appliance service technician to have 

this service preformed.
Do NOT attempt to replace the 

batteries used in this product with any 

other type of battery.

WARNING: NEVER use ordinary 

batteries for replacement, as these may 

leak and damage your vacuum cleaner. 

Use only battery pack XB14726 provided by 

EURO-PRO Operating LLC for 

replacement.

CAUTION: NEVER use the unit 

without the battery compartment cover 

in place.

NOTE: Any other servicing should be 

performed by an authorized service 

representative.

1. Make sure that the intended wall area 

for the wall mounting bracket to be 

drilled is free from any hidden 

electrical wires, water pipes and gas 

lines.

2. Select an appropriate place close to a 

wall power outlet (120V., 60 Hz).

3. Do not mount near direct sunlight, 

near a heat source or outdoors.

4. Select an appropriate drill type for the 

material to be drilled. 

5. Carefully measure and mark the 

location of all bracket holes and

then drill holes and screw the  wall    

mounting bracket onto the wall.

The battery pack of your SV726N is 

replaceable, however care should be 

taken when doing so. Follow these steps 

when replacement is required:

1. Using a #1 Phillips head screw driver, 

remove the single screw securing the 

battery compartment cover located on 

the under side of the unit.

2. To remove the cover, press down on 

the battery compartment cover while 

sliding towards the rear of the unit. 

NEVER open the battery 

compartment except to change the 

battery.

3. Set aside battery compartment cover 

and screw.

4. Using the same Phillips screw driver, 

remove the single screw securing the 

battery strap. Lift off the battery strap 

and set aside with screw.

5. Carefully lift out battery pack and 

disconnect the terminals.

6. Connect the terminals to the new 

battery pack taking care to connect 

the black lead (-) to the negative 

connector first and the red lead (+) to 

the positive connector second. Place 

the new battery into the battery 

compartment.

7. Tuck the wiring inside the battery 

compartment so that the wiring does 

not interfere with the battery 

compartment cover when it is 

replaced.

8. Re-install the battery strap and 

battery compartment cover.

•

Use only with the battery pack 

supplied with the unit.

• Do not attempt to remove the battery 

pack from the unit to charge it.

• Never attempt to throw the battery 

pack or unit into a fire or incinerate it.

• Do not attempt to remove or damage 

the battery casing.

• Battery must be recycled or disposed 

of properly at the end of it's 

service life.

clean the dust cup filter after each use.
1. To remove the dust cup container, 

press down on the dust cup release 

button and pull off  the dust cup 

container.

2. Pull out the dust cup filter.

3. Empty the dust from the dust cup 

container. (See Fig. 7)

4. Rinse the dust cup filter in cold water, 

and then wait until it dries completely 

before replacing it back into the dust 

cup container. Do not use a washing

machine to clean the dust cup filter. 

Do not use a hair dryer to dry it. Air 

5. Replace the dust cup filter carefully 

into the dust cup compartment. 

NEVER operate vacuum cleaner 

without dust cup filter in place.

6. Attach the dust cup container to the 

cordless vacuum.

Fig. 7

1. Remove the vacuum cleaner from 

the charging base

2. Make sure that it is in the "Off" 

position.

3. Firmly insert the motorized brush  

(Fig. 5) into the air-intake nozzle of 

the dust cup container ensuring 

that the contact pins are engaged 

in the connector slots of the unit. 

(Fig. 6)

Please note that this motorized 

brush is for vacuuming short pile 

carpets or rugs.

Fig. 6

Fig. 5

Metal 

contact 

pins

NOTE: It is recommended that the dust 

cup filter be replaced every three (3) 

months to ensure peak performance of 

the unit.

CAUTION: The suction hole must be 

open and free of any obstructions at all 

times. Otherwise, the motor will 

overheat and could become damaged.

WARNING: NEVER use ordinary 

batteries for replacement, as these may 

leak and damage your vacuum cleaner.

WARNING: Do not touch the