Rover 45048 用户手册

Rover Mowers Limited 

Model 45 

Rover Mowers Limited 

Model 45 

TM

TM

TM

TM

1.  Lift the top off the carton base and place to one 

side.

2.  Pivot  the  upper  handlebars  into  the  upright 

position, and secure with the clamp screw and 

nut. Do not damage the clutch and throttle cables. 

Refer to separate sheet for details.

3.  Roll  the  mower  off  the  timber  base  of  the 

carton.

4.  To adjust the height of the handlebars:-

  a. Loosen the lower handlebar securing bolts (A)

on both sides of the mower. Figure 1.

  b. Adjust the height of the handle bars, by pivoting 

them up or down, to suit the operator.

  c. Re-tighten the nuts (A) Figure 1.

1.  Place  the  mower  on  a  level  surface  in  a  well 

ventilated area.

2.  Fill the engine crankcase with 10W-30 or SAE 30 

oil to the top of the oil filler port. Refer to engine

manufacturers instructions.

3.  Fill the fuel tank with UNLEADED petrol.

4.  Ensure the spark plug lead is connected to the 

spark plug.

1.  To fit the catcher. Hold the grass catcher by the 

top edge, hook the catcher on to the two locating 

pegs on the front of the mower, positioning the 

catcher on the two rubber stops on either side of 

the mower.

2.  To  remove  the  catcher.  Disengage  the  cutter 

drive and move the throttle control lever to stop 

position. When the engine has stopped, hold the 

catcher by the top edge and lift it off the locating 

pegs.

 

Stop the engine BEFORE fitting or

 

removing the grass catcher. 

 

Read  and  understand  the  safety 

instructions  and  the  engine 

manufactuers operating instructions 

BEFORE using the mower.

1

5.1   LUBRICATION
To gain the optimum performance from your 

mower, the following areas need to be oiled every 

five hours of operation. The same grade oil as used

in the engine is suitable.

1.  Clutch Thrust Pad (1) - looking through the

left hand oil port hole in the clutch cover apply 

three drops of oil in the thrust pad oil hole. 

Figure 13.

2.  Clutch inner cone (2) - looking through the

right hand oil port hole in the clutch cover 

apply three drops of oil in the clutch inner cone 

oil hole. Figure 13. Note: in may be necessary 

to engage the clutch and slowly pull on the 

engine starter cord to align the inner cone oil 

hole with the clutch cover hole.

3.  Front roller (3) - apply six drops of oil to each

side of the shaft. Figure 14.

4.  Height adjustment knob (4) - remove the

plastic cover plug to gain access, and apply six 

drops of oil. Figure 14.

5.  Drive chains (5) - every 10 hours of operation

remove the chain case side cover and apply 

a ‘chain oil’ to the drive chains. Replace side 

cover. Figure 14.

5.2   ENGINE
For detailed cleaning and maintenance instruc-

tions, refer to the engine manufacturers operating 

manual.

5.3   GENERAL
1. 

Keep the mower free of grass and debris 

build up.

2. 

Clean any spilt oil or fuel from around the 

engine.

3. 

Regularly check that all nuts and bolts are 

secure.

4. 

After use and cleaning, lubricate the blade 

edges with oil to prevent rust build up on the 

cutting edges.

Bearings are sealed for life and do not require 

lubrication.

NOTES

6

2892 Reel Mower IMPOSED.indd   4

9/11/2005   9:12:49 AM