EchoStar dsb-808 2ci 用户手册
Section 2
EchoNAV User Interface
Page 2 - 6
Digital Satellite Receivers - Fixed
© 2
0
03 E
c
hoS
tar
Inte
Inte
rnati
o
nal
C
o
C
o
rp
orat
io
n
A
ll ri
g
h
ts
re
s
s
e
rv
ed
English
2
-
Fixed dish setup (DiSEqC1.2 only)
-
Program satellites
(DiSEqC1.2 only)
-
About EchoStar
NOTE
In a DiSEqC1.2 installation (System - DiSEqC1.2), it is possible to add one or more
fixed dishes with the help of an external switch.
fixed dishes with the help of an external switch.
■
LNBs
To set the number of LNBs you use. You only can change the
setting if you have selected a Switch in the System setup.
setting if you have selected a Switch in the System setup.
■
Polarity
To set the device that controls the Polarity (not used).
■
Switch
Shows the Switch that you have selected in the System setup.
■
LNB1
Shows the LNB1 that you have selected in the System setup.
■
LNB2, 3, 4
Select for every LNB, a pre-defined LNBs, the related SAT and
Port.
Port.
■
Check signal
Check signal verifies the settings you made before. If the
settings are correct, the TP indicator becomes green. If the
indicator becomes red, select another TP or make sure you
have selected the correct Port for this SAT.
If your TP is not listed, select TP00 which brings you to the Add
data menu.
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
settings are correct, the TP indicator becomes green. If the
indicator becomes red, select another TP or make sure you
have selected the correct Port for this SAT.
If your TP is not listed, select TP00 which brings you to the Add
data menu.
The signal indicator helps you to check the signal quality (top)
and strength (bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
■
Search channels
Search channels does a channel search on the defined SAT.
■
SAT
To define the satellite you want to search channels on.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
If your SAT is not listed, select S00 which brings you to the Add
data menu.
■
Longitude
Shows the orbital position of the defined SAT.
■
User LNB
Shows the LNB that you have selected in the System setup.
■
TP
Shows a transponder, from the internal database, of the defined
SAT. If the signal indicator shows low levels, select another TP
that gives a better signal. If your TP is not listed, select TP00
which brings you to the Add data menu.
SAT. If the signal indicator shows low levels, select another TP
that gives a better signal. If your TP is not listed, select TP00
which brings you to the Add data menu.
■
Skew
(not used).
■
Position
To move the dish and find the defined SAT.
■
Fine tune
To move the dish for best signal level and quality. The signal
indicator helps you to check the signal quality (top) and strength
(bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
indicator helps you to check the signal quality (top) and strength
(bottom) for the defined SAT and Network.
Search channels will bring you to the next menu to start the
channel search.
■
Search channels
Search channels does a channel search on the defined SAT.
■
Company
Shows the Company name.
■
Address
Shows the visit address of EchoStar.
■
EchoNAV
Shows the current EchoNAV software version.
■
Boot version
Shows the current Boot version.
■
Internet site
Shows the EchoStar Internet site.