Alcatel-Lucent 6850-48 参考指南

OmniSwitch CLI Reference Guide

page 22

DVMRP Commands

ip pim spt status {enable | disable}
ip pim state-refresh-interval seconds
ip pim state-refresh- limit ticks
ip pim state-refresh- ttl num
show ip pim sparse
show ip pim dense
show ip pim neighbor [ip_address]
show ip pim candidate-rp
show ip pim group-map [bsr | static-rp | ssm | dense]
show ip pim interface [if_name]
show ip pim static-rp
ipv6 pim sparse status {enable | disable}

bsr_address

ipv6 pim static-rp group_address/prefix_length rp_address [[no] override] [priority priority]
ipv6 pim spt status {enable | disable}
show ipv6 pim neighbor [ipv6_address] [if_name]

show ipv6 pim cbsr [scope scope_value]
show ipv6 pim bsr [scope scope_value]

ip load dvmrp
ip dvmrp status {enable | disable}
ip dvmrp flash-interval seconds
ip dvmrp graft-timeout seconds
ip dvmrp interface {interface_name}
no ip dvmrp interface {interface_name}
ip dvmrp interface {interface_name} metric value
ip dvmrp neighbor-interval seconds
ip dvmrp neighbor-timeout seconds
ip dvmrp prune-lifetime seconds
ip dvmrp prune-timeout seconds
ip dvmrp report-interval seconds
ip dvmrp route-holddown seconds
ip dvmrp route-timeout seconds
ip dvmrp subord-default {true | false}
ip dvmrp tunnel {local_name} {remote_address}
no ip dvmrp tunnel {local_name} {remote_address}
ip dvmrp tunnel {interface_name remote_address} ttl value
ip dvmrp debug-level level
ip dvmrp debug-type message_type

no ip dvmrp debug-type message_type
show ip dvmrp
show ip dvmrp interface [ip_address | interface_name | enabled | disabled]
show ip dvmrp neighbor [ip_address]
show ip dvmrp nexthop [ip_address ip_mask]
show ip dvmrp prune [group_address source_address source_mask]
show ip dvmrp route [ip_address ip_mask]
show ip dvmrp tunnel [local_address remote_address]
show ip dvmrp debug

ip mroute-boundary if_name scoped_address mask
no ip mroute-boundary if_name scoped_address mask
ipv6 mroute-boundary if_name scope scope_value
no ipv6 mroute-boundary if_name scope scope_value
ip mroute interface if_ name ttl threshold
show ip mroute-boundary
show ipv6 mroute-boundary
show ip mroute
show ip mroute interface {interface_name}
show ipv6 mroute interface {interface_name}
show ip mroute-nexthop

port mirroring port_mirror_sessionid [no] source slot/port[-port2] [slot/port[-port2]...] 

destination slot/port [rpmir-vlan vlan_id] [bidirectional |inport |outport] [unblocked 
vlan_id]
[enable | disable]

port mirroring port_mirror_sessionid {enable | disable}
no port mirroring port_mirror_sessionid {enable | disable}
port monitoring port_monitor_sessionid source slot/port 

[{no file | file filename [size filesize] | [overwrite {on | off}]}]
[inport | outport | bidirectional] [timeout seconds] [enable | disable]

port monitoring port_monitor_sessionid {disable | pause | resume}
no port monitoring port_monitor_sessionid
show port mirroring status [port_mirror_sessionid]
show port monitoring status [port_monitor_sessionid]
show port monitoring file [port_monitor_sessionid]