Alcatel-Lucent 6850-48 硬件手册
Status LEDs
OmniSwitch 6850 Series Chassis and Hardware Components
page 2-54
OmniSwitch 6850 Series Hardware Users Guide
September 2009
Status LEDs
LEDs provide visual status information. These “status lights” are used to indicate conditions, such as
hardware and software status, primary role status, power supply status, primary and secondary status
(stacked configurations), fan and temperature errors, 10 Gigabit uplink status (when applicable), slot
number information, data speed, link integrity, and activity. Refer to the diagram below for detailed infor-
mation on LED states.
hardware and software status, primary role status, power supply status, primary and secondary status
(stacked configurations), fan and temperature errors, 10 Gigabit uplink status (when applicable), slot
number information, data speed, link integrity, and activity. Refer to the diagram below for detailed infor-
mation on LED states.
Front Panel LED Descriptions (OS6850-P48X Shown)
Displays solid green when an SFP is installed in the corre-
sponding port and a link state exists; blinks green when trans-
mitting or receiving traffic; off when no activity is present or
no SFP is installed.
sponding port and a link state exists; blinks green when trans-
mitting or receiving traffic; off when no activity is present or
no SFP is installed.
By default, when an SFP is installed, it takes over the port
number of the corresponding RJ-45 Ethernet port. If an SFP is
installed in the slot labeled 45, Ethernet port 45 is no longer
available and cannot be used for 10/100/1000 traffic. For
detailed information on changing combo port settings, see
“Configuring Ethernet” in the Network Configuration Guide.
number of the corresponding RJ-45 Ethernet port. If an SFP is
installed in the slot labeled 45, Ethernet port 45 is no longer
available and cannot be used for 10/100/1000 traffic. For
detailed information on changing combo port settings, see
“Configuring Ethernet” in the Network Configuration Guide.
OmniSwitch 6850-P48
USB
OK
PRI
PWR
BPS
Console
CLASS 1 LASER PRODUCT
1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Slot Indicator LED
The slot indicator LED dis-
plays the switch’s current slot
number. Displays 0 when the
switch is booting.
The slot indicator LED dis-
plays the switch’s current slot
number. Displays 0 when the
switch is booting.
Ethernet Port LEDs
10/100/1000 Ethernet port have one built-in status
LED. This LED indicate the data speed and link/
activity either PoE or non-PoE status for each corre-
sponding Ethernet port. 1000 Mbps SFP and 10000
Mbps XFP have a single LED for activity. See
10/100/1000 Ethernet port have one built-in status
LED. This LED indicate the data speed and link/
activity either PoE or non-PoE status for each corre-
sponding Ethernet port. 1000 Mbps SFP and 10000
Mbps XFP have a single LED for activity. See
for more information.
Link/Activity LED
Link/Activity LED
Combo Port Status LEDs
OK. Solid green when the switch has passed hard-
ware diagnostic tests and the system software is
operational. Solid amber when a hardware or sys-
tem software failure occurs. Blinks green during
normal diagnostics.
ware diagnostic tests and the system software is
operational. Solid amber when a hardware or sys-
tem software failure occurs. Blinks green during
normal diagnostics.
PRI. Solid green when the switch is either a
stand-alone switch or the primary switch in a
stack; solid amber if the switch status is second-
ary; off if the switch is idle (i.e., neither primary
or secondary).
stand-alone switch or the primary switch in a
stack; solid amber if the switch status is second-
ary; off if the switch is idle (i.e., neither primary
or secondary).
PWR. Solid green when the primary
(i.e., factory-installed) power supply sta-
tus is OK and the power supply is oper-
ating normally. Solid amber in the event
of a power supply failure.
(i.e., factory-installed) power supply sta-
tus is OK and the power supply is oper-
ating normally. Solid amber in the event
of a power supply failure.
BPS. Solid green when an optional
redundant power supply is installed and
operational. Solid amber if a redundant
power supply failure occurs; off when
no redundant power supply is installed.
redundant power supply is installed and
operational. Solid amber if a redundant
power supply failure occurs; off when
no redundant power supply is installed.
System Status LEDs