RCA vr676hf 用户指南
40
Recording a Program
Using Two VCRs for Copying and Editing Tapes
Operating Instructions
(Refer to hookup on page 8.)
Use this VCR as the playback VCR and the other as the recording VCR. If you have two compatible VCR’s, use the
AutoEdit feature described below.
AutoEdit feature described below.
1.
Turn on the TV and VCRs.
2.
Tune TV to the VCR viewing channel, either 3, 4, or TV’s
video input.
video input.
3.
If you have connected your VCR using Option A (page 8),
tune recording VCR to channel 3 or 4 — the one selected on
the back of the playback VCR.
tune recording VCR to channel 3 or 4 — the one selected on
the back of the playback VCR.
If you have connected your VCR using Option B (page 8),
press INPUT on recording VCR’s remote to select the line
input. Select L1 to record from jacks on the back, or L2 to
record from jacks on the front.
press INPUT on recording VCR’s remote to select the line
input. Select L1 to record from jacks on the back, or L2 to
record from jacks on the front.
4.
Insert the tape you want to copy into playback VCR. Insert
a blank tape with safety tab in place into recording VCR.
a blank tape with safety tab in place into recording VCR.
To prevent recording on-screen displays from the playback
VCR, press DISPLAY three times. See page 24 for details.
VCR, press DISPLAY three times. See page 24 for details.
5.
Press PLAY, then PAUSE on playback VCR when you reach
the point on the tape or program where you want to begin
copying. If the tape was not recorded on the playback
VCR, streaks may appear and you may need to adjust
tracking.
the point on the tape or program where you want to begin
copying. If the tape was not recorded on the playback
VCR, streaks may appear and you may need to adjust
tracking.
6.
Press RECORD, then PAUSE, on recording VCR.
7.
Press PAUSE buttons on both VCRs at the same time to
begin copying the tape.*
begin copying the tape.*
8.
Edit out segments that you do not want to copy by pressing
PAUSE on recording VCR to stop copying the tape. Then
locate the next segment you want to copy on the playback
VCR by using FWD, REW, and PLAY
PAUSE on recording VCR to stop copying the tape. Then
locate the next segment you want to copy on the playback
VCR by using FWD, REW, and PLAY
.
Press PAUSE on the
playback VCR. Press PAUSE at the same time on both
VCRs to resume copying.
VCRs to resume copying.
9.
Press STOP on both VCRs when you are finished.
* You may turn off the TV after the recording has started as it
does not have to be on to copy a tape.
Using Dual Remote with AutoEdit
TM
Use this VCR as the playback VCR and set it to respond to VCR2•LD on the remote as
described on page 14. Use your other compatible VCR as the recording VCR, which should
respond to VCR1
described on page 14. Use your other compatible VCR as the recording VCR, which should
respond to VCR1
.
1.
Follow steps 1 – 4 in the “Operating Instructions” above.
2.
Press VCR1 on remote to control recording VCR. Press
RECORD, then PAUSE, to put recording VCR in pause
mode.
RECORD, then PAUSE, to put recording VCR in pause
mode.
3.
Press VCR2•LD on remote to control playback VCR.
4.
Use FF, REW, and PLAY to locate the point where you want
to begin copying. Press PAUSE while VCR is playing to
put playback VCR in pause mode.
to begin copying. Press PAUSE while VCR is playing to
put playback VCR in pause mode.
5.
Press EDIT on remote to start the VCRs copying.
6.
Press EDIT again when you want to stop the tape from
copying.
copying.
7.
Repeat steps 4 – 6 as needed.
8.
Press VCR1, STOP, then VCR2•LD, STOP, when you are
finished.
finished.
Caution: The unauthorized
recording of television
programs and other
materials may infringe the
rights of others.
recording of television
programs and other
materials may infringe the
rights of others.