Toshiba tdp-t100u 用户手册
21
20
Preparations
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting menu
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting menu
, in accordance with your needs.
Placement
WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
Floor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection
Ceiling-mounted rear projection
Operating a computer using the remote control
A computer can be operated using the projector’s remote control. This function is available
on any computer with the Windows
on any computer with the Windows
®
98/98SE, Windows
®
Me, Windows
®
2000, or Win-
dows
®
XP OS, that is equipped with a USB port which can support USB1.1 (The mouse
remote control receiver is also supported on OS 9 or OS X for the Macintosh). However,
please note that Toshiba does not guarantee the operation of all computers.
please note that Toshiba does not guarantee the operation of all computers.
1
Connecting a computer
Connect the mouse remote control receiver (supplied) to a computer.
Mouse remote control receiver
To USB port
2
Operating a computer
Operate remote control’s buttons towards the mouse remote control receiver.
● Moving the mouse pointer
● Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
then press.
● To left click
Press the L-CLICK button.
● To right click
Press the R-CLICK button.
● To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
pointer is over the desired location, then release the L-CLICK button.
● Using the computer’s page up [↑] and down [↓] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint
®
slides.
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front
Remote Control Rear
PAGE –
PAGE +
R-CLICK
L-CLICK
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
Screen
As seen from above
As seen from the side
90
°
a
90
°
Lens center
a (min length) =
projection size (inches) – 1.0437
26.957
a (max length) =
projection size (inches) – 0.6246
16.749
a is the distance (m) between the lens and the screen, and
corresponds to a range of 1.07 m to 11.09 m.
corresponds to a range of 1.07 m to 11.09 m.
projection
projection distance a (m)
min length
max length
size (inches)
(zooming max) (zooming min)
30
1.07
1.75
40
1.45
2.35
60
2.19
3.55
80
2.93
4.74
100
3.67
5.93
150
5.53
8.92
200
7.38
–
250
9.24
–
300
11.09
–