Toshiba tdp-wx5400u 用户指南
78
79
Others
Compatible input signal list
The following table shows compatible signal types, their resolution and frequency refresh rates.
Horizontal: 15 kHz, 31 kHz to 90 kHz, Vertical: 50 Hz to 85 Hz
Signal
Resolution (DPI)
Frequency Refresh
Rate (KHz)
Frequency Refresh
Rate (Hz)
NTSC
-
15.73
60.00
PAL
-
15.63
50.00
PAL60
-
15.73
60.00
SECAM
-
15.63
50.00
VESA
D
640 x 480
31.47
59.94
MAC
D
640 x 480
35.00
66.67
VESA
D
640 x 480
37.86
72.81
VESA
D
640 x 480
37.50
75.00
VESA
D
640 x 480
43.27
85.01
VESA
D
800 x 600
35.16
56.25
VESA
D
800 x 600
37.88
60.32
VESA
D
800 x 600
48.08
72.19
VESA
D
800 x 600
46.88
75.00
VESA
D
800 x 600
53.67
85.06
MAC
D
832 x 624
49.72
74.55
VESA
D
1024 x 768
48.36
60.00
VESA
D
1024 x 768
56.48
70.07
MAC
D
1024 x 768
60.24
74.93
VESA
D
1024 x 768
60.02
75.03
VESA
D
1024 x 768
68.68
85.00
VESA
D
1152 x 864
67.50
75.00
VESA
D
1280 x 768
47.80
60.00
VESA
D
1280 x 768
60.30
75.00
VESA
D
1280 x 768
68.60
85.00
VESA
D
1280 x 800
49.70
60.00
VESA
D
1280 x 800
62.80
75.00
VESA
D
1280 x 800
71.60
85.00
VESA
D
1280 x 960
60.00
60.00
VESA
D
1280 x 1024
63.98
60.02
VESA
D
1400 x 1050
65.30
60.00
VESA
D
1440 x 900
55.90
60.00
VESA
D
1440 x 900
70.60
75.00
HDTV (1080i)(1125i)
-
1920 x 1080
33.75
60.00 Interlace
HDTV (1080i)(1125i)
-
1920 x 1080
28.13
50.00 Interlace
HDTV (720p)(750p)
-
1280 x 720
45.00
60.00 Progressive
HDTV (720p)
-
1280 x 720
37.50
50.00 Progressive
SDTV (576p)(625p)
-
-
31.25
50.00 Progressive
SDTV (480p)(525p)
-
-
31.47
59.94 Progressive
DVD YCbCr
-
-
15.73
59.94 Interlace
DVD YCbCr
-
-
15.63
50.00 Interlace
Note
Images above flagged with “D” are supported by digital signal.
An image with higher or lower resolution than the projector’s native resolution
(1280 x 800) will be compressed.
Some Composite and Sync on Green signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If
this should happen, change the refresh rate or resolution on your PC. Refer to Display
Properties help section of your PC for procedures.
•
•
•
•
Specifications (Continued)
CONTROL terminal
Pin assignment
Pin
No.
Signal Name
Description
D sub 9 pin connector
1
DCD
Data carrier detect
2
RXD
Receiving data
3
TXD
Sending data
4
DTR
Data terminal ready
5
GND
Signal ground
6
DSR
Data set ready
7
RTS
Request to send
8
CTS
Consent to send
9
RI
Ring indicator
Note
Use a cross cable (not supplied) for RS232C control.
Interface format
<Command format>
Header:
‘#’
Delimiter:
CR (0x0Dh)
Command: 3 Byte (ASCII Character)
Parameter: Variable length
(If the command has a parameter, place a colon before the parameter.)
<Response format>
Header:
‘=’
Delimiter
CR (0x0Dh)
Command
3 Byte (ASCII Character, command echo)
Parameter
Variable length
(If the command has a parameter, place a colon before the parameter.)
Main Commands
Item
Command
Power off
PON
Shutdown
PSD
Status display on
DON
Status display off
DOF
Note
Contact your dealer for control cable and other commands.
•
•