Toshiba tlp-x150u 用户指南
44
45
Operations
•
[Interval]
You can set the display interval of time (in seconds or minutes) for slide shows to be
played automatically.
played automatically.
Note
It may take time to display slide show with some files.
•
[Display effect]
When playing a slide show, the projector can give various display effects or transitions
to each slide being displayed.
The transitions available are listed below:
to each slide being displayed.
The transitions available are listed below:
•
None
Displays each slide with no display effects.
•
Wipe
Displays the next slide with a gradual upward (Wipe
↑
), downward (Wipe
↓
), to the left
(Wipe
←
), or to the right (Wipe
→
), over the current slide.
•
Dissolve
Displays the next slide gradually in a certain fixed block pattern over the current slide.
•
Cover
Displays the next slide as sliding upward (Cover
↑
), downward (Cover
↓
), to the left
(Cover
←
), or to the right (Cover
→
), over the current slide.
•
[Play icon]
The slideshow icon can be displayed.
•
Standard
The projector handles the slideshow icon as follows depending on the “On/Off” setting
of Icon on the projector’s menu.
Icon On: The projector displays the icon upon the start of playing a slide show and
of Icon on the projector’s menu.
Icon On: The projector displays the icon upon the start of playing a slide show and
turns it off after a few seconds.
Icon Off: The projector does not display the icon.
•
Continuous
The projector keeps the icon displayed during the slide show.
•
[Thumbnail display]
Select the form of a thumbnail list.
All: Displays a thumbnail preview of JPEG files, and if any JPEG files exist in the
All: Displays a thumbnail preview of JPEG files, and if any JPEG files exist in the
folder displays the leading thumbnail image.
File: Displays only a thumbnail image of JPEG files. The thumbnail image of the JPEG
files in the folder is not displayed.
Off: Displays an icon without displaying thumbnail preview.
•
[Unplug device]
Run when unplugging a USB memory, a USB memory card reader/writer or a digital
camera and the like.
camera and the like.
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Computer Y/P
B
/P
R
Video
S-video
USB
memory
Input
Input source name
Yes
Yes
Yes
Yes
Yes
Mode name
RGB input mode
[Note 1]
Yes
No
No
No
No
Resolution
Resolution (in dots)
Yes
No
No
No
No
Frequency
Sync frequency
Yes
No
No
No
No
Sync
Sync signal polarity
[Note ]
Yes
No
No
No
No
Signal format
Y/P
B
/P
R
signal format
No
Yes
No
No
No
Video mode
Color method of video signal
No
No
Yes
Yes
No
Lamp time
Time of lamp use
[Note ]
Yes
Yes
Yes
Yes
Yes
Lamp reset count
The count for lamp replacement
Yes
Yes
Yes
Yes
Yes
Total time
The total time that this projector
is used.
is used.
Yes
Yes
Yes
Yes
Yes
Version
Firmware version
[Note 4]
Yes
Yes
Yes
Yes
Yes
Notes
1:
The mode of supported RGB signals
is shown.
:
Sync signal polarity shown as P (positive) or N (negative) for [H/V].
: Displays [Lamp time] as an estimated measure of when the lamp should be replaced.
(Cannot be used as a counter of guaranteed lamp time.) When the displayed time
approaches ,000 hours, consult with a dealer about getting replacement lamp
TLPLW1 (sold separately).
approaches ,000 hours, consult with a dealer about getting replacement lamp
TLPLW1 (sold separately).
4: [Version] shows the version of the projector’s internal control program. This version will
be requested for customer service purposes.
Note
The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
information, dismiss the display, then display it again.
•
Using the menus (Continued)