Mitsubishi hs-u448 用户手册
25
5
The hour numbers of the start time will flash. Press the
ADJUST buttons to set the hour when recording is to start.
Press ENTER.
ADJUST buttons to set the hour when recording is to start.
Press ENTER.
6
The minute numbers of the start time will flash. Press the
ADJUST buttons to set the minutes when recording is to
start. Press ENTER.
ADJUST buttons to set the minutes when recording is to
start. Press ENTER.
7
Set the stop time the same way as the start time, using
steps 5 and 6.
steps 5 and 6.
8
Press the ADJUST buttons to set the recording speed:
SP = standard play; EP = extended play; AUTO = auto.
Auto speed programming is discussed on page 28. Press
ENTER.
SP = standard play; EP = extended play; AUTO = auto.
Auto speed programming is discussed on page 28. Press
ENTER.
IMPORTANT
If you press ENTER when you set the timer recording
incompletely, Current Program is not completed will appear
on your screen.
incompletely, Current Program is not completed will appear
on your screen.
If two programmed recording times overlap, VCR is already
programmed for that time will display on your screen for
about 3 seconds, and then the Recap screen will appear.
The program you have just set will be highlighted in
magenta color and flash for 3 seconds. The start and stop
time of the overlapped program will be highlighted in cyan
color. You will need to erase one of them.
programmed for that time will display on your screen for
about 3 seconds, and then the Recap screen will appear.
The program you have just set will be highlighted in
magenta color and flash for 3 seconds. The start and stop
time of the overlapped program will be highlighted in cyan
color. You will need to erase one of them.
9
The programmed memory will appear on the Recap screen.
10 To program additional recording times, select an empty
program line by pressing ADJUST buttons. Press ENTER.
The Program to record menu will appear. Continue the
programming procedure from step 3.
The Program to record menu will appear. Continue the
programming procedure from step 3.
11 When you are finished with all programming, check the following:
• If you have a cable box, leave the cable box turned ON
and tuned to the station you wish to record. Additionally, if
you are using an A/B switch, remember to set the switch
to the correct position.
you are using an A/B switch, remember to set the switch
to the correct position.
• Turn the VCR power OFF and make sure the programmed
recording light is lit.
IMPORTANT
When programmed recording of 4 and under are entered,
only 4 of the 8 program lines appear on the Recap screen
at any one time. To see additional program lines, press the
ADJUST buttons to scroll the lines on the screen.
only 4 of the 8 program lines appear on the Recap screen
at any one time. To see additional program lines, press the
ADJUST buttons to scroll the lines on the screen.
Canceling a recording in progress
There are two ways to cancel a recording in progress:
Press STOP. The recording stops, but the program is not
cancelled. Therefore, if you press REC, the recording will start
again.
cancelled. Therefore, if you press REC, the recording will start
again.
Press POWER on the front panel. The recording stops and the
program is cancelled.
program is cancelled.
2
1
3
5
4
6
8
7
9
0
STOP
STOP
Programming not cancelled
¬Program to record
ƒChannel 2
ƒDay Monday 11
ƒStart time 11:30am
ƒStop time 1:30pm
ƒRecord speed
SP
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select
Recap screen
¬Program to record
CH DAY ON OFF
10 TH14 9:00pm 10:30pm SP
§
2 MO11 11:30am 1:30pm SP
--- -- --:-- --:-- SP
--- -- --:-- --:-- SP
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select
¬Program to record
ƒChannel 2
ƒDay Monday 11
ƒStart time
11:00am
ƒStop time --:--
ƒRecord speed AUTO
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select
Timer Recording
POWER
Programming cancelled