Sony STR-DA6400ES 产品宣传页

STRDA6400ESUC 3-875-815-11(1) GB

You can set up the speakers to obtain the desired sound from all 

connected speakers automatically by using the auto calibration 

function.

During the calibration, the sound that comes out of the speakers is very 

loud. Pay attention to the presence of children or to the effect on your 

neighborhood.

Perform the measurement in a quiet environment to avoid the effect of noise 

and get a more accurate measurement.

If there are any obstacles in the path between the optimizer microphone and 

the speakers, the calibration cannot be performed correctly. Remove any 

obstacle from the measurement area to avoid measurement error.

For detail, see front page. 

the AUTO CAL MIC jack.
The AUTO CAL MIC jack is used for the supplied optimizer 

microphone only. Do not connect other microphones. Doing 

so may damage the receiver and the microphone.

Place the optimizer microphone at your seating position. Use 

a stool or tripod so that the optimizer microphone remains 

at the same height as your ears. Orient the L end of the 

optimizer microphone toward the front left speaker and the 

R end of the optimizer microphone toward the front right 

speaker.

When a subwoofer is connected, turn on the subwoofer and turn 

up the volume beforehand. Turn the MASTER VOLUME knob 

to just before the mid-point.
If you connect a subwoofer with the crossover frequency 

function, set the value to maximum.
If you connect a subwoofer with an auto standby function, set it 

to off (deactivated).

The auto calibration function allows you to measure the following: 

speaker connections, polarity of speakers, speaker distance, 

speaker angle, speaker size, speaker level, frequency characteristics.

Refer to “3: Connecting the monitor” in the operating 

instructions.

Switch the input of the TV so that an image of the menu is 

displayed.

The receiver can be operated using the remote.

After “GUI MODE ON” has appeared in the display window 

of the receiver, “GUI MODE” appears.

The menu is displayed on the TV screen.

  Press / repeatedly to select “  Settings,” then 

press   or .

The Settings menu list appears on the TV screen.

  Press / repeatedly to select “Auto Calibration,” 

then press   or .

  Press / repeatedly to select “Quick Setup,” then 

press   .
The screen on which you can select the item to be measurered 

appears.

  Press / repeatedly and   to un-check the items 

you do not want to measure, then press .

The confirmation screen, asking whether you are ready to 

start measurement, appears.

The measurement starts in five seconds.

When the measurement ends, a beep sounds and the 

measurement result appears on the TV screen.

  Press / repeatedly to select “Yes,” then press 

The selecting screen of the calibration type appears.













  Press / repeatedly to select the auto calibration 

Full Flat

Makes the measurement of frequency from 

each speaker flat.

Engineer

Sets the frequency to one that matches that 

of the Sony listening room standard.

Front Reference

Adjusts the characteristics of all the 

speakers to match the characteristics of the 

front speaker.

OFF

Sets the auto calibration EQ to off.

The measurement results are saved.

  Press .

The exit screen appears.

When “Save auto calibration (auto speaker setup)?” appears on 

the TV screen in step 10, you can select whether to confirm the 

warning (“Yes”) or not (“No”). Follow the instructions of the TV 

screen when you select “Yes.” For details on warning and error 

codes, see “Message list after auto calibration measurement” in “9: 

Calibrating the appropriate speaker settings automatically (Auto 

Calibration)” in the operating instructions.

The size of a speaker (LARGE/SMALL) is determined by the low characteristics. 

The measurement results may vary, depending on the position of the optimizer 

microphone and speakers, and the shape of the room. It is recommended that 

you follow the measurement results. However, you can change those settings 

in the Speaker settings menu. Save the measurement results first, then try to 

change the settings if you want.

You can select the language to be used for messages on the TV 

screen from 4 languages. 

English
Español
Français
Deutsch

For details, see “

 System settings” in the operation instructions.

You should set up each component so that take out sound is 

output from speakers correctly when you play back a connected 

component. The following case describes Sony components. Refer 

to the operating instructions supplied with each component.

Select a suitable playback area (multi-channel or 2 channel). 

Sound may come out from only the front speaker left/right when 2 

channel is selected. 

The receiver is now ready to use. Refer to the operating instruction 

supplied with the receiver for details.









AUTO CAL MIC

GUI MODE

 /  ,   / 

 /  ,   / 

 /  ,  

 /  ,   , 

 /  ,  

