Sony STR-DG1100 手册

STR-DG2100/STR-DG1100 3-274-908-11(2) GB

You can set up the speakers to obtain the desired sound from all 

connected speakers automatically by using the auto calibration 

function.

During the calibration, the sound that comes out of the speakers is very 

loud. Pay attention to the presence of children or to the effect on your 

neighborhood.

Perform the measurement in a quiet environment to avoid the effect of noise 

and get a more accurate measurement.

If there are any obstacles in the path between the optimizer microphone and 

the speakers, the calibration cannot be performed correctly. Remove any 

obstacle from the measurement area to avoid measurement error.

For detail, see front page. 

the AUTO CAL MIC jack.
The AUTO CAL MIC jack is used for the supplied optimizer 

microphone only. Do not connect other microphones. Doing 

so may damage the receiver and the microphone.

Place the optimizer microphone at your seating position. Use 

a stool or tripod so that the optimizer microphone remains at 

the same height as your ears.

When a sub woofer is connected, turn on the sub woofer and 

turn up the volume beforehand. Turn the MASTER VOLUME 

knob to just before the mid-point.
If you connect a sub woofer with the crossover frequency 

function, set the value to maximum.
If you connect a sub woofer with an auto standby function, set it 

to off (deactivated).

The auto calibration function allows you to measure the following: 

speaker connections, polarity of speakers, speaker distance, 

speaker size, speaker level, frequency characteristics.

Refer to “3: Connecting the monitor” in the operating 

instructions.

Switch the input of the TV so that an image of the menu is 

displayed.

The menu list of this receiver appears on the TV screen. 

Press AMP MENU if the menu list does not appear on the 

TV screen. The menu appears on the TV screen when “GUI 

MODE” appears on the display.

  Press / repeatedly to select “Settings,” then 

press   or .

The Settings menu list appears on the TV screen.

  Press / repeatedly to select “Auto Calibration,” 

then press   or .

  Press / repeatedly to select “Quick Setup,” then 

  Press / repeatedly and   to un-check the items 

Speaker Distance

Speaker Level

Frequency Characteristic

  Press .

The measurement process will take approximately 30 

seconds with a test tone. Wait until the measurement process 

completes.

When the measurement ends, a beep sounds and the 

measurement result appears on the TV screen. 

The displayed unit of distance for models for US and Canada is feet. The 

unit of distance for models for countries/areas other than US and Canada 

is meters. You can change the unit of distance use in “Distance Unit” in the 

Speaker settings menu.

  Press / repeatedly to select “Yes,” then press 

















  Press / repeatedly to select the auto calibration 

type, then press .

The measurement results are saved.

Full Flat

Makes the measurement of frequency from 

each speaker flat.

Engineer

Sets the frequency to one that matches that 

of the Sony listening room standard.

Front Reference

Adjusts the characteristics of all the 

speakers to match the characteristics of the 

front speaker.

OFF

Sets the auto calibration to off.

The exit screen appears.

When “Save auto calibration (auto speaker setup) results?” appears 

on the TV screen in step 14, you can select whether to confirm 

the warning (“Yes”) or not (“No”). Follow the instructions of the 

TV screen when you select “Yes.” For details on warning and error 

codes, see “Message list after auto calibration measurement” in “9: 

Calibrating the appropriate speaker settings automatically (Auto 

Calibration)” in the operating instructions.

You cannot measure the speaker height of the surround speakers and the 

surround back speakers. Set the position of the surround speaker from the 

“Position” in the Speaker settings menu.

The size of a speaker (LARGE/SMALL) is determined by the low 

characteristics. The measurement results may vary, depending on the position 

of the optimizer microphone and speakers, and the shape of the room. It is 

recommended that you follow the measurement results. However, you can 

change those settings in the Speaker settings menu. Save the measurement 

results first, then try to change the settings if you want.

Press 

 on the remote when “Please Press ENTER” appears on the TV 

screen.

You should set up each component so that take out sound is 

output from speakers correctly when you play back a connected 

component. The following case describes Sony components. Refer 

to the operating instructions supplied with each component.

Select a suitable playback area (multi-channel or 2 channel). 

Sound may come out from only the front speaker left/right when 2 

channel is selected. 

The receiver is now ready to use. Refer to the operating instruction 

supplied with the receiver for details.





AUTO CAL MIC

AMP MENU

 /  ,   / 

 /  ,   / 

 /  , 

 /  , 

 /  , 