Roland Fantom-Xa 业主指南
133
Editing Songs
When using Loop Play or Loop Recording, you can use the loop
points you specify here to specify the repeated area, as an alternative
to repeating the specified number of measures.
points you specify here to specify the repeated area, as an alternative
to repeating the specified number of measures.
*
It is not possible to assign a loop point to a pattern.
1.
Press [SONG EDIT <-> LIST] to access the SONG EDIT
screen.
2.
Press [F1 (LOOP)].
The Loop Play window appears.
fig.LoopPlay
3.
Move the cursor to the desired parameter, and use the
VALUE dial or [INC] [DEC] to make the setting.
4.
If you press [LOOP PLAY] to make it light, or press [F5
(LOOP)] to add a check mark (
✔
); looping will be turned on.
Track Edit lets you edit areas of sequencer data that you specify.
1.
Access the SONG LIST screen, and then load the song you
2.
Press [SONG EDIT <-> LIST] to access the SNG EDIT (TRK)
screen.
3.
Press [F5 (EDIT)].
The Track Edit window appears.
fig.TrackEdit
4.
Press [F3 (
)] [F4 (
)] or
to select the desired
function, and then press [F6 (SELECT)].
For details on the setting windows of each track editing
function, refer to the following explanations of each function.
function, refer to the following explanations of each function.
5.
Set the parameters for each function. Press [CURSOR] to
move the cursor to the desired parameter, and use the
VALUE dial or [INC] [DEC] to set the value. First check the
region that is to be affected by the editing operation, and
then make corrections if you want to change it.
VALUE dial or [INC] [DEC] to set the value. First check the
region that is to be affected by the editing operation, and
then make corrections if you want to change it.
6.
Press [F6 (EXEC)] to execute the operation.
When the operation is completed, the display will briefly
indicate “Completed!”
indicate “Completed!”
*
If you decide not to execute the operation, press [F5 (CANCEL)].
If you are not satisfied with the results of executing the
function, you can press [ERASE/UNDO] to return to the state
prior to executing the operation (Undo/Redo). After executing
Undo, you can use Redo to revert to the previous state. After
executing Undo, you can execute Redo by performing the above
procedure once again.
function, you can press [ERASE/UNDO] to return to the state
prior to executing the operation (Undo/Redo). After executing
Undo, you can use Redo to revert to the previous state. After
executing Undo, you can execute Redo by performing the above
procedure once again.
Specifying the Area of a Song that
will Repeat (Loop Points)
will Repeat (Loop Points)
Parameter
Explanation
Repeat Times
Number of repeats
Value:
INF, 1–99
If you want repetition to continue until you
press [STOP], set this to “INF.”
press [STOP], set this to “INF.”
Start Point (
S
)
Location at which repetition is to begin
If you press [F3 (START)], the current location
of the song will be set as the starting location.
of the song will be set as the starting location.
End Point (
E
)
Location at which repetition will end
If you press [F4 (END)], the current location of
the song will be set as the ending location.
the song will be set as the ending location.
* The location you specify here will not be included
in the repeated area.
Editing Sequencer Data
Over the Specified Range
(Track Edit)
Over the Specified Range
(Track Edit)
Basic Operation for Track Editing
Change Velocity
(p. 139)
(p. 139)
Change Channel
(p. 139)
(p. 139)
Fantom-Xa_e.book 133 ページ ２００４年１０月２２日 金曜日 午後２時３分