Roland Fantom-Xa 业主指南
162
Adding Effects
Here we will explain how to make multi-effects settings in Performance mode.
fig.MFXSetting
*
In this setting screen, you can edit the parameters of the multi-effects that is selected by the Multi-effects Type setting. For details on the parameters that
can be edited, refer to
can be edited, refer to
Parameters marked by
can be selected as a multi-effect control destination parameter (see below).
In Patch mode, the Keyboard part can use MFX1 and the Pad part can use MFX2.
fig.MFXCtrl
*
Press [F5 (CTRL)] to switch the multi-effects that will be modified.
*
In patch/rhythm set mode, there are parameters that determine, for each tone/rhythm tone, whether or not Pitch Bend, Controller Number 11 (Expression)
and Controller Number 64 (Hold 1) are received (p. 51). When these settings are “ON,” and the MIDI messages are received, then when any change is
made in the settings of the desired parameter, the Pitch Bend, Expression, and Hold1 settings also change simultaneously. If you want to change the
targeted parameters only, then set these to “OFF.”
and Controller Number 64 (Hold 1) are received (p. 51). When these settings are “ON,” and the MIDI messages are received, then when any change is
made in the settings of the desired parameter, the Pitch Bend, Expression, and Hold1 settings also change simultaneously. If you want to change the
targeted parameters only, then set these to “OFF.”
Making Multi-Effects Settings (MFX1–3)
Parameter
Value
Explanation
(Multi-Effects Type)
00–78
Selects from among the 78 available multi-effects.
Making Multi-Effects Settings (MFX Control)
Parameter
Value
Explanation
Source 1–4
OFF, CC01–31, 33–95,
PITCH BEND,
AFTERTOUCH,
SYS CTRL1–4
PITCH BEND,
AFTERTOUCH,
SYS CTRL1–4
MIDI message used to change the multi-effects parameter with the multi-effects control
OFF:
Multi-effects control will not be used.
CC01–31, 33–95:
Controller numbers 1–31, 33–95
PITCH BEND:
Pitch Bend
AFTERTOUCH:
Aftertouch
SYS CTRL1–4:
MIDI messages used as common multi-effects controls
If you want to use common controllers for the entire Fantom-Xa, select “SYS CTRL1”–”SYS
CTRL4.” MIDI messages used as System Control 1–4 are set with the Sys Ctrl 1–4 Source param-
eters (p. 196).
CTRL4.” MIDI messages used as System Control 1–4 are set with the Sys Ctrl 1–4 Source param-
eters (p. 196).
Destination 1–4
Multi-effects parameters to be controlled with the multi-effects control
The multi-effects parameters available for control will depend on the multi-effects type. For de-
tails, refer to
tails, refer to
Sens 1–4
-63– +63
Amount of the multi-effects control’s effect that is applied
To make an increase in the currently selected value (to get higher values, move to the right, in-
crease rates, and so on), select a positive value; to make a decrease in the currently selected value
(to get lower values, move to the left, decrease rates, and so on), select a negative value. For either
positive or negative settings, greater absolute values will allow greater amounts of change. Set
this to “0” if you don’t want to apply the effect.
crease rates, and so on), select a positive value; to make a decrease in the currently selected value
(to get lower values, move to the left, decrease rates, and so on), select a negative value. For either
positive or negative settings, greater absolute values will allow greater amounts of change. Set
this to “0” if you don’t want to apply the effect.
Fantom-Xa_e.book 162 ページ ２００４年１０月２２日 金曜日 午後２時３分