Roland Fantom-Xa 业主指南
82
Modifying the Sound in Real Time
You can use the D Beam controller to control the pads as an
alternative to striking the pads themselves.
alternative to striking the pads themselves.
1.
Hold down [SHIFT] and press D BEAM [PAD TRIGGER].
A screen like the following appears.
fig.DBeamTrig
2.
Press
to select the parameter.
3.
Use the VALUE dial or [INC] [DEC] to make the setting.
4.
Press [EXIT] to return to the previous screen.
PAD trigger settings are saved independently for each
performance as part of the performance settings. This lets you
create performances that make effective use of controller
settings.
performance as part of the performance settings. This lets you
create performances that make effective use of controller
settings.
If Patch mode is selected, this is saved as part of the system
settings. If you want to save the settings, press [F6 (WRITE)].
settings. If you want to save the settings, press [F6 (WRITE)].
You can assign various functions to the D Beam controller and apply
a wide range of effects to the sound in real time.
a wide range of effects to the sound in real time.
1.
Hold down [SHIFT] and press D BEAM [ASSIGNABLE].
A screen like the following appears.
fig.DBeamAsgn
2.
Press
to select the parameter.
3.
Use the VALUE dial or [INC] [DEC] to make the setting.
4.
Press [EXIT] to return to the previous screen.
The settings for the ASSIGNABLE are saved independently for
each performance as part of the performance settings. This lets
you create performances that make effective use of controller
settings.
each performance as part of the performance settings. This lets
you create performances that make effective use of controller
settings.
If Patch mode is selected, this is saved as part of the system
settings. If you want to save the settings, press [F6 (WRITE)].
settings. If you want to save the settings, press [F6 (WRITE)].
Pad Trigger
Parameter
Value
Explanation
Pad Number
1–9
Pad number affected by the D Beam
Pad Velocity
1–127
Strength of the pad sound played by the D Beam controller
Pad Control Mode
MOMENTARY,
LATCH
LATCH
Specifies how the D Beam will behave when it is obstructed.
MOMENTARY:
The parameter will be on only while the D Beam is obstructed, and will turn off
when you stop obstructing it.
LATCH:
The parameter will alternately be switched on/off each time you obstruct the D Beam.
Assignable
Parameter
Value
Explanation
Type
CC01–31, 33–95,
BEND UP,
BEND DOWN,
START/STOP,
TAP TEMPO,
ARP GRID,
ARP DURATION,
ARP MOTIF,
ARP OCTAVE UP,
ARP OCTAVE DOWN
BEND UP,
BEND DOWN,
START/STOP,
TAP TEMPO,
ARP GRID,
ARP DURATION,
ARP MOTIF,
ARP OCTAVE UP,
ARP OCTAVE DOWN
Function controlled by the D Beam controller
CC01–31, 33–95:
Controller numbers 1–31, 33–95
BEND UP:
BEND DOWN:
START/STOP:
Starts/Stops the sequencer.
TAP TEMPO:
Tap tempo (a tempo specified by the interval at which you move your hand over the
D Beam controller).
ARP GRID:
Arpeggio Grid
ARP DURATION:
Duration of each arpeggiated note
ARP MOTIF:
Arpeggio Motif
ARP OCTAVE UP:
The range in which the arpeggio is sounded will rise in steps of an octave (max-
imum 3 octaves).
ARP OCTAVE DOWN:
The range in which the arpeggio is sounded will lower in steps of an octave
(maximum 3 octaves).
Range Min
0–127
Lower limit of the range of the D Beam controller
Range Max
0–127
Upper limit of the range of the D Beam controller.
By setting Range Max below Range Min you can invert the range of change.
Fantom-Xa_e.book 82 ページ ２００４年１０月２２日 金曜日 午後２時３分