Roland GW-7 业主指南
10
Introduction
1.
If you want to use your left and right hands to play different
Tones, press KEYBOARD [SPLIT] so the button is lit.
Tones, press KEYBOARD [SPLIT] so the button is lit.
The Tone you selected in Main mode (i.e., when [SPLIT] and
[DUAL] were extinguished) will be the Tone for the Upper Part.
[DUAL] were extinguished) will be the Tone for the Upper Part.
2.
Select a different Tone for each Part.
1.
To select the Tone for the Upper Part, press [UPPER] so the
button is lit. To select the Tone for the Lower Part, press
[LOWER] so the button is lit.
button is lit. To select the Tone for the Lower Part, press
[LOWER] so the button is lit.
2.
Turn the VALUE dial to step through the Tones one by
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
3.
Play the keyboard.
Turn the VOLUME knob to adjust the volume.
The split point is set to
C4
(note number
60
).
In Split mode, the most suitable octave settings for each tone are
applied automatically.
applied automatically.
If you press and hold [SPLIT] (for approximately two seconds),
the split point setting screen will appear. You can turn the
VALUE dial to change the split point. When you’re finished,
press [EXIT].
the split point setting screen will appear. You can turn the
VALUE dial to change the split point. When you’re finished,
press [EXIT].
If you press and hold [UPPER] or [LOWER] (for approximately
two seconds), the volume setting screen for each part will
appear. You can turn the VALUE dial to adjust the volume of
each part. When you’re finished, press [EXIT].
two seconds), the volume setting screen for each part will
appear. You can turn the VALUE dial to adjust the volume of
each part. When you’re finished, press [EXIT].
You can’t select a drum set Tone for the Lower Part.
1.
If you want to play two Tones simultaneously, press
KEYBOARD [DUAL] so the button is lit.
KEYBOARD [DUAL] so the button is lit.
2.
Select two Tones.
1.
To change the Tone that you selected in Main mode, press
UPPER so the button is lit. To change the second Tone that
you want to layer with the first Tone, press [LOWER] so
the button is lit.
UPPER so the button is lit. To change the second Tone that
you want to layer with the first Tone, press [LOWER] so
the button is lit.
2.
Turn the VALUE dial to step through the Tones one by
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
3.
Play the keyboard.
Turn the VOLUME knob to adjust the volume.
If you press and hold [UPPER] or [LOWER] (for approximately
two seconds), the volume setting screen for each part will
appear. You can turn the VALUE dial to adjust the volume of
each part. When you’re finished, press [EXIT].
two seconds), the volume setting screen for each part will
appear. You can turn the VALUE dial to adjust the volume of
each part. When you’re finished, press [EXIT].
You can’t select a drum set Tone as the second Tone.
It’s convenient to use the metronome when you’re practicing a new
song.
song.
1.
Hold down [SHIFT] and press [ENTER] (METRONOME).
The metronome setting screen will appear, and the metronome
will begin sounding.
will begin sounding.
2.
Use SELECT [
][
] and turn the VALUE dial to specify
the time signature and volume for the metronome.
3.
To stop the metronome, hold down [SHIFT] and press
[ENTER] (METRONOME).
[ENTER] (METRONOME).
1.
Press [FUNCTION].
2.
Use SELECT [
][
] to get the screen to indicate
“Utility?”, and then press [ENTER].
3.
Use SELECT [
][
] to get the screen to indicate
“Factory Reset?”
4.
Press [ENTER]. The screen will prompt “Sure?”
5.
Press [ENTER] to initialize the GW-7.
If you press [EXIT] instead, you’re returned to the previous
screen and no initialization takes place.
Once the initialization is complete, the previous screen will
reappear.
screen and no initialization takes place.
Once the initialization is complete, the previous screen will
reappear.
Restoring the factory settings will initialize the System, User
Tone, and User Performance settings.
Tone, and User Performance settings.
1.
Press [FUNCTION].
2.
Use SELECT [
][
] to get the screen to indicate
“Utility?”, and then press [ENTER].
3.
Use SELECT [
][
] to get the screen to indicate “Init
IntDRV?”
4.
Press [ENTER]. The screen will prompt “Sure?”
5.
Press [ENTER] to initialize the settings.
If you press [EXIT] instead, you’re returned to the previous
screen and no initialization takes place.
Once the initialization is complete, the previous screen will
reappear.
screen and no initialization takes place.
Once the initialization is complete, the previous screen will
reappear.
Using Split Mode
Using Dual Mode
Using the Metronome
Restoring the GW-7 to Its
Factory Settings
Initializing the User Style
and User Song Memory
GW-7_e.book 10 ページ ２００５年２月１６日 水曜日 午前８時４８分