Roland JUNO-D 业主指南
85
Adding effects
Effects
46:TUMBLING DLY (Tumbling Delay)
This is a delay that first produces “tumbling” delayed repeats, and
then echoes the original sound.
then echoes the original sound.
It is most effective when applied to single notes of a “one-shot”
sound.
sound.
fig.MFX-46
47: FBK RIPPER (Feedback Ripper)
This effect repeatedly cuts the sound, and outputs a delayed sound
for the cut portion. You can create new phrases by applying this to a
drum phrase or other phrase.
for the cut portion. You can create new phrases by applying this to a
drum phrase or other phrase.
fig.MFX-47
Reset
OFF, ON
This setting determines whether
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
Low Gain
-15– +15 [dB]
Adjusts the gain of the low fre-
quency.
quency.
High Gain
-15– +15 [dB]
Adjusts the gain of the high fre-
quency.
quency.
Level
0–127
Adjusts the output level.
Parameter
Value
Description
Type
TYPE1–TYPE6
Selects one of the six available
types for the number of delay
sounds heard in time “A” in the
diagram below.
types for the number of delay
sounds heard in time “A” in the
diagram below.
Pre Delay
0–500 [ms]
Adjusts time “A” in the diagram
below.
below.
Delay Time
0–345 [ms]
Adjusts time “B” in the diagram
below.
below.
HF Damp
200–8000 [Hz],
BYPASS
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Feedback #
-98– +98 [%]
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Parameter
Value
Description
RESET
LEVEL
L in
R in
L out
R out
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
Feedback
Tumbling Delay
Level
original tone
A
B
B
Balance #
D100:0W–
D0:100W
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level
0–127
Adjusts the output level.
Parameter
Value
Description
Mod Wave
TRI, SQR, SIN,
SAW1/ 2
SAW1/ 2
TRI: The sound will be cut by a
triangle wave.
SQR: The sound will be cut by a
square wave.
SIN: The sound will be cut by a
sine wave.
SAW1/2: The sound will be cut
by a sawtooth wave. The teeth in
SAW1 and SAW2 point at oppo-
site directions.
triangle wave.
SQR: The sound will be cut by a
square wave.
SIN: The sound will be cut by a
sine wave.
SAW1/2: The sound will be cut
by a sawtooth wave. The teeth in
SAW1 and SAW2 point at oppo-
site directions.
Rate #
0.05–10.00 [Hz],
note *2
note *2
Adjusts the frequency (speed) of
the change.
the change.
Depth #
0–127
Sets the depth to which the ef-
fect is applied.
fect is applied.
Delay Left
0–420 [ms], note
*1
*1
Adjusts the time from the direct
sound until the left delay sound
is heard.
sound until the left delay sound
is heard.
Delay Right
0–420 [ms], note
*1
*1
Adjusts the time from the direct
sound until the right delay
sound is heard.
sound until the right delay
sound is heard.
Dly Feedback
-98– +98 [%]
Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Reset
OFF, ON
This setting determines whether
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
the period for the pattern is reset
(ON), or not (OFF) when sounds
are played.
While the rhythm guide is play-
ing, the period for the pattern is
not reset even if you set this ON.
Level
0–127
Adjusts the output level.
Parameter
Value
Description
R in
R out
L in
L out
Feedback
Feedback
Feedback
2-Band
EQ
2-Band
EQ
Delay
Delay
Ripper
Ripper
SAW1
SAW2
JUNO-D_e.book 85 ページ ２００４年６月１１日 金曜日 午後１時２１分