Roland JUNO-D 业主指南
90
Settings common to all modes (System Function)
Pedal (Pedal Control Assign)
This specifies the function of the pedal connected to the CONTROL
PEDAL jack.
PEDAL jack.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
pedal to apply the following effects.
TAP TEMPO:
C1 (C1 Knob Assign)
C2 (C2 Knob Assign)
C3 (C3 Knob Assign)
Select the effects that will be controlled by the [C1]/[C2]/[C3] knobs.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
pedal to apply the following effects.
PATCH MODIFY:
The effect indicated on the panel will be
controlled (p. 26).
controlled (p. 26).
* If you assign any effects other than PATCH MODIFY to the [C1]/
[C2]/[C3] knobs, you must switch the
Patch Modify select button
to [ENV] (envelope). If [BALANCE/LFO] is selected, the balance and
LFO will change.
LFO will change.
* If you are using the [C1]/[C2]/[C3] knobs in Performance mode to
setting will determine the part whose effect will be controlled.
If
If
MFX Source
is set to “Part1–16,” the effect of that part will be
the part whose effect will be controlled. If this setting is “OFF,” no
effect will be controlled.
effect will be controlled.
Settings related to MIDI (MIDI)
Patch Rx Ch (Patch Receive Channel)
Specifies the receive channel of MIDI messages in Patch mode.
VALUE:
1–16
Patch Tx Ch (Patch Transmit Channel)
Specifies the transmit channel of MIDI messages in Patch mode. If
you do not want to transmit MIDI messages to external MIDI
devices, turn this parameter “OFF.” If you want the transmit channel
to always match the Patch Receive Channel, set this parameter to
“RxCh.”
you do not want to transmit MIDI messages to external MIDI
devices, turn this parameter “OFF.” If you want the transmit channel
to always match the Patch Receive Channel, set this parameter to
“RxCh.”
VALUE:
1–16, RxCh, OFF
Perform Ctrl Ch (Performance Control Channel)
Performance Ctrl Ch selects the MIDI receive channel used during
switching of performances when MIDI messages (Program Change/
Bank Select) are sent from an external MIDI device. Set this to “OFF”
if performances are not to be switched from an external MIDI device.
switching of performances when MIDI messages (Program Change/
Bank Select) are sent from an external MIDI device. Set this to “OFF”
if performances are not to be switched from an external MIDI device.
VALUE:
1–16, OFF
If only a program change is received, and if the Perform Ctrl Ch
parameter setting coincides with the MIDI receive channel of a
part, priority will be given to switching the performance.
parameter setting coincides with the MIDI receive channel of a
part, priority will be given to switching the performance.
If this is set to 1–16, the JUNO-D will transmit MIDI messages
(program change/bank select) on that channel when the
performance is switched.
(program change/bank select) on that channel when the
performance is switched.
Rx Prog Chg (Receive Program Change Switch)
Specifies whether Program Change messages will be received (ON)
or not (OFF).
or not (OFF).
VALUE:
OFF, ON
Rx Bank Sel (Receive Bank Select Switch)
Specifies whether Bank Select messages will be received (ON) or not
(OFF).
(OFF).
VALUE:
OFF, ON
Rx Sys Exc (Receive System Exclusive Switch)
Specifies whether System Exclusive messages will be received (ON)
or not (OFF).
or not (OFF).
VALUE:
OFF, ON
Tx Prog Chg (Transmit Program Change
Switch)
Switch)
Specifies whether Program Change messages will be transmitted
(ON) or not (OFF).
(ON) or not (OFF).
VALUE:
OFF, ON
Tx Bank Sel (Transmit Bank Select Switch)
Specifies whether Bank Select messages will be transmitted (ON) or
not (OFF).
not (OFF).
VALUE:
OFF, ON
JUNO-D_e.book 90 ページ ２００４年６月１１日 金曜日 午後１時２１分