Roland JUNO-D 业主指南
95
Performing with an external MIDI device
Performing with an
external MIDI device
Setting the patch receive channel
When you have finished connecting the external MIDI device, match
JUNO-D’s Receive channel with the external MIDI device’s Transmit
channel. Here we will explain the settings for using the JUNO-D in
Patch mode.
JUNO-D’s Receive channel with the external MIDI device’s Transmit
channel. Here we will explain the settings for using the JUNO-D in
Patch mode.
1.
Press [SYSTEM] so it is lit.
2.
Use PAGE/CURSOR [
]/[
] to select “Patch Rx Ch”
(patch receive channel).
fig.r10-11_40
By holding down [SHIFT] and using PAGE/CURSOR [
]/
[
3.
Use VALUE [-]/[+] to modify the value.
VALUE
1–16:
Performance data of each part will be received on
the selected channel.
the selected channel.
Setting the program change receive
switch
Then, to enable tones to be switched from the external MIDI device,
set the Receive Switch for Program Change and Bank Select to ON.
Factory settings have these set to ON.
set the Receive Switch for Program Change and Bank Select to ON.
Factory settings have these set to ON.
1.
Press [SYSTEM] so it is lit.
2.
Use PAGE/CURSOR [
]/[
] to select “Rx Prog Chg”
(Receive Program Change Switch) and “Rx Bank Sel”
(Receive Bank Select Switch).
3.
Use VALUE [-]/[+] to set both parameters to “ON.”
4.
Press [WRITE] to save the settings.
For further information, refer to
Press [EXIT] to cancel the operation and return to the previous page.
* For instructions on setting the external MIDI device’s Transmit
channel, refer to the owner’s manual for that device.
* If you are using Performance mode, you will also need to set “Receive
Sw,” “Receive Prg Chg,” and “Receive Bank Sel” for each part in
addition to the settings described above (p. 57).
addition to the settings described above (p. 57).
Selecting JUNO-D sounds from an
external MIDI device
external MIDI device
Transmitting Bank Select (Controller Numbers 0 & 32) and Program
Change messages from the external MIDI device to the JUNO-D
allows you to switch patches and rhythm sets.
Change messages from the external MIDI device to the JUNO-D
allows you to switch patches and rhythm sets.
1.
Transmit a value for the Bank Select MSB (controller number
0) (BnH 00H mmH) message to the JUNO-D.
2.
Transmit a value for the Bank Select LSB (controller number
32) (BnH 20H llH) message to the JUNO-D.
3.
Transmit a Program Change (CnH ppH) to the JUNO-D.
n:
MIDI channel number
mm, ll:
Bank number
pp:
Program number
The “Perform Ctrl Ch” (Performance Control Channel) setting
lets you switch performances in Performance mode. With the
factory settings, this is set to “OFF”; performances will not be
switched.
lets you switch performances in Performance mode. With the
factory settings, this is set to “OFF”; performances will not be
switched.
Bank number/program number
correspondence table
correspondence table
The MIDI messages transmitted by an external MIDI device
correspond with patches/rhythm sets on the JUNO-D as shown in
the following table.
correspond with patches/rhythm sets on the JUNO-D as shown in
the following table.
* If the Program numbers on your external MIDI device are referenced as
values from 0 to 127, find the appropriate number by subtracting 1
from the number in the following correspondence chart.
from the number in the following correspondence chart.
* When the JUNO-D receives a Program Change message without
receiving the Bank Select, it switches to the patch or rhythm set with
the same Bank number as the currently selected patch or rhythm set.
the same Bank number as the currently selected patch or rhythm set.
For details on how numbers in the table correspond to the sound
of the JUNO-D, refer to
of the JUNO-D, refer to
Performance
Patch
Group
Number
Bank Number
Program
Number
Number
MSB
LSB
User
001–008
085
000
001–008
Preset
001–032
085
064
001–032
Group
Number
Bank Number
Program
Number
Number
MSB
LSB
User
001–128
087
000
001–128
Preset
001–128
087
064
001–128
129–256
087
065
001–128
257–384
087
066
001–128
385–512
087
067
001–128
513–640
087
068
001–128
GM Patch
001–256
121
000–
001–128
JUNO-D_e.book 95 ページ ２００４年６月１１日 金曜日 午後１時２１分