Roland JUNO-G 业主指南
121
Editing a Audio Phrase (Sample)
5.
Press [F6 (EXEC)].
A message will ask you for confirmation.
6.
To execute, press [F6 (EXEC)].
*
To cancel, press [F5 (CANCEL)].
In some cases, the audio quality will be improved if you boost the
high-frequency range of an imported sample. Also, the high-
frequency range of the sample may be emphasized when you use a
sampler made by another manufacturer. In this case, you can
minimize the change in tonal character by attenuating the high-
frequency range.
high-frequency range of an imported sample. Also, the high-
frequency range of the sample may be emphasized when you use a
sampler made by another manufacturer. In this case, you can
minimize the change in tonal character by attenuating the high-
frequency range.
*
You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F1 (TRUNC&EMPHS)], and then press [F2 (EMPHS)].
fig.EMPHASIS
3.
Use the VALUE dial or [INC] [DEC] to select the emphasis
type.
PreEmphasis:
Emphasizes the high-frequency range.
DeEmphasis:
Attenuates the high-frequency range.
4.
If you want to replace the current sample with the
emphasized sample, press [F4 (OVER WRITE)] to display
the “
the “
✔
” mark.
5.
Press [F6 (EXEC)].
A message will ask you for confirmation.
6.
To execute, press [F6 (EXEC)].
*
To cancel, press [F5 (CANCEL)].
This operation raises the level of the entire sample as much as
possible without exceeding the maximum level. It is a good idea to
boost the volume by executing the Normalize operation.
possible without exceeding the maximum level. It is a good idea to
boost the volume by executing the Normalize operation.
*
You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F2 (NORM & AMP)], and then press [F1 (NORM)].
fig.NORMALIZE
3.
If you want to replace the current sample with the
normalized sample, press [F4 (OVER WRITE)] to display the
“
“
✔
” mark.
4.
Press [F6 (EXEC)].
A message will ask you for confirmation.
5.
To execute, press [F6 (EXEC)].
*
To cancel, press [F5 (CANCEL)].
This operation adjusts the volume of the entire sample. You can also
apply an envelope (time-variant change) to the volume of the sample.
apply an envelope (time-variant change) to the volume of the sample.
*
You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F2 (NORM & AMP)], and then press [F2 (AMP)].
fig.AMP
3.
If you want to adjust the volume of the entire sample, use the
VALUE dial or [INC] [DEC] to set the rate of volume boost.
4.
If you want to apply an envelope, specify points.
Press [F3 (POINT)] to display the “
✔
” mark. Then press [
]
[
] to select a parameter, and then use the VALUE dial or
[INC] [DEC] to set the value.
5.
If you want to replace the current sample with the edited
sample, press [F4 (OVER WRITE)] to display the “
✔
” mark.
6.
Press [F6 (EXEC)].
A message will ask you for confirmation.
7.
To execute, press [F6 (EXEC)].
*
To cancel, press [F5 (CANCEL)].
Boosting or Limiting the High-
frequency Range of the Sample
(EMPHASIS)
frequency Range of the Sample
(EMPHASIS)
Maximizing the Volume of a
Sample (NORMALIZE)
Sample (NORMALIZE)
AMP
Parameter
Explanation
Rate
Rate of volume boost:
0–400%
Specifies how much boost will be applied relative to the
current volume
current volume
Parameter
Explanation
Current
Point
Point
Currently selected point
Beginning near the start point, the points will be num-
bered 1, 2, 3, or 4.
bered 1, 2, 3, or 4.
Point 1–4
Location of the current point
Rate 1–4
Amplification ratio of the current point:
0–400%
Specifies how the volume of each point is to be boosted
relative to the current value.
relative to the current value.
JUNO-G_e.book 121 ページ ２００６年７月３１日 月曜日 午後２時４９分