Roland JUNO-G 业主指南
47
Creating a Patch
How to Apply the LFO
STEP
Pan Depth
★
-63– +63
How deeply the LFO will affect the pan
Positive (+) and negative (-) settings for the Depth parameter result in differing kinds of change in pitch and volume. For example, if you set
the Depth parameter to a positive (+) value for one tone, and set another tone to the same numerical value, but make it negative (-), the modu-
lation phase for the two tones will be the reverse of each other. This allows you to shift back and forth between two different tones, or combine
it with the Pan setting to cyclically change the location of the sound image.
the Depth parameter to a positive (+) value for one tone, and set another tone to the same numerical value, but make it negative (-), the modu-
lation phase for the two tones will be the reverse of each other. This allows you to shift back and forth between two different tones, or combine
it with the Pan setting to cyclically change the location of the sound image.
* When the Structure parameter is set to any value from “2” through “10,” the output of tones 1 and 2 will be combined into tone 2, and the output of tones
3 and 4 will be combined into tone 4. This applies to the Pan Depth parameter settings. For this reason, tone 1 will follow the settings of tone 2, and tone
3 will follow the settings of tone 4 (p. 35).
3 will follow the settings of tone 4 (p. 35).
●
Apply the LFO gradually after the key is pressed
Fade Mode:
ON <
Delay Time:
Time from when the keyboard is played until the LFO begins to be applied
Fade Time:
Time over which the LFO amplitude will reach the maximum after the Delay
Time has elapsed
●
Apply the LFO immediately when the key is pressed, and then gradually begin to decrease the effect
Fade Mode:
ON >
Delay Time:
Time that the LFO will continue after the keyboard is played
Fade Time:
Time over which the LFO amplitude will reach the minimum after the Delay
Time has elapsed
●
Apply the LFO gradually after the key is released
Fade Mode:
OFF <
Delay Time:
Time from when the keyboard is released until the LFO begins to be applied
Fade Time:
Time over which the LFO amplitude will reach the maximum after the Delay
Time has elapsed
●
Apply the LFO from when the key is pressed until it is released, and gradually begin to decrease the
effect when the key is released
Fade Mode:
OFF >
Delay Time:
Time that the LFO will continue after the keyboard is released
Fade Time:
Time over which the LFO amplitude will reach the minimum after the Delay
Time has elapsed
Parameter
Value
Explanation
Step Type
TYP1, TYP2
When generating an LFO waveform from the data specified in LFO Step 1–16, specify whether the level will change abruptly
at each step or will be connected linearly.
at each step or will be connected linearly.
TYP1:
stair-step change
TYP2:
linear change
Step 1–16
-36– +36
Specifies the data for the Step LFO.
If the LFO Pitch Depth is +63, each +1 unit of the step data corresponds to a pitch of +50 cents.
Parameter
Value
Explanation
Note on
high (more)
low (less)
Pitch
Cutoff Frequency
Level
Pan
Delay
Time
Time
Fade Time
Depth
Note on
high (more)
low (less)
Delay Time
Fade Time
Depth
Pitch
Cutoff Frequency
Level
Pan
high (more)
low (less)
Delay
Time
Time
Fade Time
Depth
Note
off
Note
on
Pitch
Cutoff Frequency
Level
Pan
Note on
high (more)
low (less)
Delay
Time
Time
Fade Time
Depth
Note off
Pitch
Cutoff Frequency
Level
Pan
JUNO-G_e.book 47 ページ ２００６年７月３１日 月曜日 午後２時４９分