Roland RS-70 业主指南
126
Settings common to all modes (System Function)
Settings related to controllers
(CONTROLLER)
Mod (Modulation Assign)
You can use the modulation lever to apply the following effects
other than vibrato.
other than vibrato.
In Patch mode, the modulation lever will affect the patch. In Pattern
mode, the modulation lever will affect the patch that is assigned to
the current part. Use [DESTINATION TONE] to specify the tone that
will be affected (p. 30).
mode, the modulation lever will affect the patch that is assigned to
the current part. Use [DESTINATION TONE] to specify the tone that
will be affected (p. 30).
“TxCC#” refers to the controller number of the control change
message sent from the MIDI OUT connector when the modulation
lever is operated. When set to AFTERTOUCH, Channel Aftertouch
messages are sent. Set to AFTERTOUCH mainly when you want to
control an external sound generator with Aftertouch messages.
message sent from the MIDI OUT connector when the modulation
lever is operated. When set to AFTERTOUCH, Channel Aftertouch
messages are sent. Set to AFTERTOUCH mainly when you want to
control an external sound generator with Aftertouch messages.
Receiving these control change message from the MIDI IN connector
produces the same effect as operating the modulation lever.
produces the same effect as operating the modulation lever.
* When set to MFX PARAMETER1 or MFX PARAMETER2, be sure
to note the following.
LOFI (p. 109), Level is changed regardless of whether MFX
PARAMETER1 or MFX PARAMETER2 is selected.
PARAMETER1 or MFX PARAMETER2 is selected.
* When making the LFO RATE, LFO DEPTH or LFO DELAY settings,
the effect achieved differs depending on whether [FILTER LFO] is on or
off. When [FILTER LFO] is off, the LFO alters the pitch (vibrato
effect). When [FILTER LFO] is on, the LFO changes the Filter Cutoff
frequency (wah effect).
off. When [FILTER LFO] is off, the LFO alters the pitch (vibrato
effect). When [FILTER LFO] is on, the LFO changes the Filter Cutoff
frequency (wah effect).
Pedal (Pedal Control Assign)
This specifies the function of the pedal connected to the CONTROL
PEDAL jack.
PEDAL jack.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
pedal to apply the following effects.
PUNCH IN/OUT:
Use the pedal to start or stop manual punch-in/
out recording (p. 69).
out recording (p. 69).
TAP TEMPO:
C1 (C1 Knob Assign)
C2 (C2 Knob Assign)
C3 (C3 Knob Assign)
Select the effects that will be controlled by the [C1]/[C2]/[C3] knobs.
VALUE
In addition to the items listed in Modulation Assign, you can use the
pedal to apply the following effects.
pedal to apply the following effects.
PATCH MODIFY:
The effect indicated on the panel will be
controlled (p. 30).
controlled (p. 30).
* If you assign any effects other than PATCH MODIFY to the [C1]/
[C2]/[C3] knobs, you must switch the
Patch Modify select button
to [ENV] (envelope). If [BALANCE/LFO] is selected, the balance and
LFO will change.
LFO will change.
* If you are using the [C1]/[C2]/[C3] knobs in Pattern mode to control
determine the part whose effect will be controlled.
If
If
MFX Source
is set to “Part1–16,” the effect of that part will be
whose effect will be controlled. If this setting is “OFF,” no effect will be
controlled.
controlled.
Value
Tx CC#
Function/Parameter
Changed
Changed
MODULATION
CC01
Vibrato
PORTA TIME
CC05
VOLUME
CC07
Level
BALANCE
CC08
The volume balance of LOW-
ER and UPPER tones (p. 56).
ER and UPPER tones (p. 56).
PAN
CC10
EXPRESSION
CC11
Level
PORTAMENTO
CC65
SOSTENUTO
CC66
Holds the sound of the key be-
ing pressed
ing pressed
SOFT
CC67
Softens the tone
RESONANCE
CC71
RELEASE TIME
CC72
Tone Envelope Release Time
(p. 59)
(p. 59)
ATTACK TIME
CC73
CUTOFF
CC74
DECAY TIME
CC75
LFO RATE
CC76
LFO DEPTH
CC77
LFO DELAY
CC78
CHO SEND LEVEL
CC93
REV SEND LEVEL
CC91
MFX PARAMETER1
CC12
The parameter specified by
Multi-effect Control 1 (p. 95)
Multi-effect Control 1 (p. 95)
MFX PARAMETER2
CC13
The parameter specified by
Multi-effect Control 2 (p. 95)
Multi-effect Control 2 (p. 95)
AFTERTOUCH
----
RS-70_e4.book 126 ページ 2003年8月18日 月曜日 午前9時47分