Roland RS-70 业主指南
64
Creating a rhythm set (Patch mode)
• Specifying the amount of signal sent to the effect
Chorus Send Lvl (Chorus Send Level)
Sets the level of the signal sent to chorus for each tone.
VALUE:
0–127
Reverb Send Lvl (Reverb Send Level)
Sets the level of the signal sent to reverb for each tone.
VALUE:
0–127
Saving a rhythm set (User
Rhythm Set)
Once you have edited a rhythm set to your liking, use the following
procedure to save it.
procedure to save it.
1.
Press [PATCH] so it lights and you are in Patch mode.
2.
Select the rhythm set that you want to edit.
3.
Edit the rhythm set and its rhythm tones.
4.
When the rhythm set is to your liking, press [WRITE].
Use VALUE [-]/[+] to specify the number in which the rhythm
set is to be saved (U01–U16).
set is to be saved (U01–U16).
fig.r04-01_40
As shown above, the display will show only the rhythm set
number if nothing has yet been saved to that number.
number if nothing has yet been saved to that number.
Be aware that your previously saved settings will be overwritten
and lost if you save to a number in which a rhythm set has
already been saved.
and lost if you save to a number in which a rhythm set has
already been saved.
5.
Press [ENTER].
Unlike a patch, a rhythm set is always saved in the “RHYTHM &
SFX” category group “DRM” (DRUMS).
SFX” category group “DRM” (DRUMS).
For more about the category group, refer to
When the rhythm set has been saved, the display will indicate
“COMPLETED.” This completes the procedure.
“COMPLETED.” This completes the procedure.
If you decide not to save the rhythm set, press [EXIT].
If you do not change
(p. 63), the
rhythm set will have the same name as the one you selected in step 2.
Convenient functions for
rhythm set editing (Rhythm Set
Utility)
Rhythm Set Utility provides functions that you will find convenient
when editing a rhythm set, such as initializing a rhythm tone or
copying effect settings.
when editing a rhythm set, such as initializing a rhythm tone or
copying effect settings.
Copying effect settings from a
rhythm set (RHY PRM COPY)
This operation copies effect settings from an existing rhythm set to
the currently selected rhythm set. The following three parameters
can be copied.
the currently selected rhythm set. The following three parameters
can be copied.
• MFX:
Copy the multi-effect settings.
• CHORUS: Copy the chorus settings.
• REVERB:
Copy the reverb settings.
1.
Press [PATCH] so it lights and you are in Patch mode.
Select the copy-destination rhythm set.
2.
Press [UTILITY].
3.
Use PAGE/CURSOR [
]/[
] to select “1:RHY PRM
COPY.”
4.
Press [ENTER].
5.
Use VALUE [-]/[+] to select “MFX,” “CHORUS,” or
“REVERB.”
fig.r04-15_40
6.
Press PAGE/CURSOR [
].
Use VALUE [-]/[+] to specify whether you will copy
“RHYTHM” effect settings or “PTN (Pattern)” effect settings.
“RHYTHM” effect settings or “PTN (Pattern)” effect settings.
7.
Press PAGE/CURSOR [
].
Copying “RHYTHM” effect settings
Select the copy-source rhythm set.
fig.r04-16_40
Copying “PTN (Pattern)” effect settings
Select the copy-source pattern.
fig.r04-17_40
8.
Press [ENTER].
The effect settings will be copied to the currently selected
rhythm set.
rhythm set.
When the data has been copied, the display will indicate
“COMPLETED.” This ends the procedure.
“COMPLETED.” This ends the procedure.
RS-70_e4.book 64 ページ ２００３年８月１８日 月曜日 午前９時４７分