Roland v-synth xt 补充手册

 

■

 

*

Not received in Multitimbre mode or Performance mode when the Receive Switch
parameter (MULTITIMBRE/MIDI or PERFORM/MIDI) is OFF.

 

●

 

Status

2nd byte

3rd byte

8nH

kkH

vvH

9nH

kkH

00H

n = MIDI channel number:

0H - FH (ch.1 - 16)

kk = note number:

00H - 7FH (0 - 127)

vv = note off velocity:

00H - 7FH (0 - 127)

 

●

 

Status

2nd byte

3rd byte

9nH

kkH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

kk = note number:

00H - 7FH (0 - 127)

vv = note on velocity:

01H - 7FH (1 - 127)

 

●

 

Status

2nd byte

3rd byte

AnH

kkH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

kk = note number:

00H - 7FH (0 - 127)

vv = Polyphonic Key Pressure:

00H - 7FH (0 - 127) 

 

●

 

*

If the corresponding Controller number is selected for the Patch Control Source 1, 2, 3, 4,
5, 6, 7 or 8 parameter (PATCH Edit Com Matrix Ctrl), the corresponding effect will
occur.

 

❍

 

Status

2nd byte

3rd byte

BnH

00H

mmH

BnH

20H

llH

n = MIDI channel number:

0H - FH (ch.1 - 16)

mm, ll = Bank number:

00 00H - 7F 7FH (bank.1 - bank.16384)

*

Not received when the Receive Bank Select (SYSTEM Com MIDI/USB) is OFF.

*

The Patches corresponding to each Bank Select are as follows.

 

 BANK SELECT     | PROGRAM   | PATCH
 MSB | LSB       | NUMBER    | NUMBER
-----+-----------+-----------+-----------
 087 | 000       | 001 - 128 | 001 - 128
     | 001       | 001 - 128 | 129 - 256
     | 002       | 001 - 128 | 257 - 384
     | 003       | 001 - 128 | 385 - 512

 

❍

 

Status

2nd byte

3rd byte

BnH

05H

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Portamento Time:

00H - 7FH (0 - 127)

 

❍

 

Status

2nd byte

3rd byte

BnH

06H

mmH

BnH

26H

llH

n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB

 

❍

 

Status

2nd byte

3rd byte

BnH

07H

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Volume:

00H - 7FH (0 - 127)

 

❍

 

Status

2nd byte

3rd byte

BnH

0AH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Panpot:

00H - 40H - 7FH (Left - Center - Right), 

 

❍

 

Status

2nd byte

3rd byte

BnH

0BH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Expression:

00H - 7FH (0 - 127)

 

❍

 

Status

2nd byte

3rd byte

BnH

40H

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Control value:

00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON

 

❍

 

Status

2nd byte

3rd byte

BnH

41H

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Control value:

00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

 

❍

 

Status

2nd byte

3rd byte

BnH

42H

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Control value:

00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

 

❍

 

Status

2nd byte

3rd byte

BnH

5BH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Reverb Send Level:

00H - 7FH (0 - 127)

 

❍

 

Status

2nd byte

3rd byte

BnH

5DH

vvH

n = MIDI channel number:

0H - FH (ch.1 - 16)

vv = Chorus Send Level:

00H - 7FH (0 - 127)

 

❍

 

Status

2nd byte

3rd byte

BnH

65H

mmH

BnH

64H

llH

n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
 Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.