Roland VK-8 业主指南
47
Advanced Use
Edit mode allows you to get the most out of the VK-8’s
functions by making more detailed settings. This section
explains the functions that can be set in Edit mode. In this
owner’s manual, the process of modifying a setting is
referred to as “editing,” and the item of data that is modified
is referred to as a “parameter.”
functions by making more detailed settings. This section
explains the functions that can be set in Edit mode. In this
owner’s manual, the process of modifying a setting is
referred to as “editing,” and the item of data that is modified
is referred to as a “parameter.”
■
About the Edit Modes
There are two edit modes—one saves settings individually
for each preset, while the other stores a single value to be
used by the entire system.
for each preset, while the other stores a single value to be
used by the entire system.
System Memory
The edit mode that stores things for the entire system deals
with the following:
with the following:
• Organ rotary settings (p. 49)
• Click noise and percussion settings (p. 51)
• MIDI settings (p. 52)
• Equalizer and other settings (p. 55)
• Control pedal settings (p. 40)
• Click noise and percussion settings (p. 51)
• MIDI settings (p. 52)
• Equalizer and other settings (p. 55)
• Control pedal settings (p. 40)
Preset Memory
The edit mode that stores things on an individual preset
basis deals with the following:
basis deals with the following:
NOTE
In the case of settings that are saved for each preset, you must
save the edited settings in a preset. If you turn off the power
without saving the edited settings to a preset, your changes will
be lost.
■
Basic Procedure
Here is the basic procedure for each edit mode.
→
For details, refer to the explanation for each edit mode.
1.
Hold down the HARMONIC BAR PART [UPPER] and
[PEDAL] buttons, and press the [***] button.
The indicators of the [1]–[8] buttons will blink.
The [***] button will be a different button depending on
the edit mode that you want to set. For details, follow the
procedure for each edit mode.
the edit mode that you want to set. For details, follow the
procedure for each edit mode.
2.
Press one of the buttons from [1] through [8] to select
the parameter that you want to edit.
If there are more than eight parameters, you can access
all of them by switching the lit/dark state of the
[PRESET] button.
all of them by switching the lit/dark state of the
[PRESET] button.
3.
Turn the [VIBRATO AND CHORUS] knob to adjust
the setting.
For parameters that are switched ON/OFF, turn the
[VIBRATO AND CHORUS] knob toward the right to
switch the parameter ON, or toward the left to switch it
OFF.
[VIBRATO AND CHORUS] knob toward the right to
switch the parameter ON, or toward the left to switch it
OFF.
For parameters that have an adjustable value, turn the
[VIBRATO AND CHORUS] knob toward the right to
increase the value, or toward the left to decrease the
value.
[VIBRATO AND CHORUS] knob toward the right to
increase the value, or toward the left to decrease the
value.
At this time, the D Beam type indicator will show the
approximate value of the setting (p. 48).
approximate value of the setting (p. 48).
If you press the VIBRATO AND CHORUS [ON] button,
the setting will return to the initial value.
the setting will return to the initial value.
4.
If you want to adjust another parameter in the same
edit mode, press one of the [1]–[8] buttons to select the
parameter, and turn the [VIBRATO AND CHORUS]
knob to edit the value.
When you want to stop editing, press the HARMONIC
BAR PART [UPPER] button.
BAR PART [UPPER] button.
5.
Press the [WRITE] button to finalize the settings of the
parameters.
Parameter settings will be saved.
While the parameters are being saved, the indicators of
the [1]-[8] button will blink.
the [1]-[8] button will blink.
6.
Parameters that are edited independently for each
VK-8_e.book 47 ページ ２００５年７月２５日 月曜日 午後４時２４分