Motorola h800 快速安装指南
Multi-Color
Indicator Light
Slider
Call
Button
Volume
Buttons
Call
Button
Slider Lock Switch
(in locked position)
Function
Action
Disable/Enable the
Press and hold both
indicator light
Volume buttons at the
same time while
powering on headset
Answer a second
Tap the Call button
incoming call
End active call and
Tap the Call button
resume call on hold
Note: Resuming a call on hold is a phone-dependent feature.
If tapping the Call button does not execute action, revert to
the phone controls to resume call on hold.
If tapping the Call button does not execute action, revert to
the phone controls to resume call on hold.
Note: When indicator light is disabled, light does not display
for any headset function. Re-enable indicator light by pressing
and holding both Volume buttons at the same time while
powering on headset.
for any headset function. Re-enable indicator light by pressing
and holding both Volume buttons at the same time while
powering on headset.
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H800.
Features and
Functions Guide
H800
Slider
Bluetooth® Headset
TURNING HEADSET
ON AND OFF
To turn your headset on, press the Call
button to extend the slider. The indicator
light flashes blue (if paired with another
device), or is steadily blue (if ready to be
paired).
To turn your headset off, push the slider
closed. The indicator light flashes blue three
times.
EARHOOKS AND YOUR
HEADSET
Your H800 headset is supplied with multiple size
earhooks. The earhook is attached onto a hinge pin,
and is placed onto your ear when using your
headset. To install an earhook on your headset:
2 Pull Earhook Up
Hinge Pin
1 Open Earhook
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
Turn the headset power off.
Press the Volume button you want to
assign as the "volume up" button and
press the Call button to extend the slider
(to power on the headset). The indicator
light flashes three times in blue.
1
2
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
• All other relevant EU Directives.
European Union Directives
Conformance Statement
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
Hereby, Motorola declares that this
product is in compliance with:
MAKING CALLS
Function
Action
Make a voice dial call
Tap the Call button
and speak the
name after the tone
End a call
Tap the Call button
Answer a call
Tap the Call button
Ignore a call
Press and hold either
Volume button until
incoming call stops
ringing
Redial last call
Press and hold the
Call button for at least
2 seconds until you
hear a beep
Mute or unmute a call
Tap both Volume
buttons
Note: Some features are phone/network dependent.
Note: Your H800 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which profile
your phone supports. See your phone's user's guide for more
information.
Profiles. Accessing call functions depends upon which profile
your phone supports. See your phone's user's guide for more
information.
AUDIO TONES
Audio Tone
Headset Status
Ascending tone
Powering on
Descending tone
Powering off
Two ascending
Pairing successful/
tones
Initiate voice dial
Ring tone
Incoming call
Two short tones when
Volume at minimum
pressing Volume button
or maximum
High/low tones
Low battery
repeated every 60 sec.
No audio indications;
No audio indications;
Out of range
deteriorating quality
Three ascending tones
Three ascending tones
Connected call/
Redial last number
Three descending tones Ended call
Two rapid ascending
Two rapid ascending
Mute enabled
tones
Two rapid descending
Two rapid descending
Mute disabled
tones
Open the attached
earhook 90 degrees from
the headset.
Gently lift and pull the
Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
Position the headset for
Position the headset for
right or left ear use (right
ear use is displayed).
Hook the bottom of the
Hook the bottom of the
earhook onto the lower
hinge pin, then lift and pull
the top of the earhook
over the upper hinge pin.
1
2
3
4
WEARING THE
HEADSET
Once you have attached your desired
earhook, follow these steps to wear your
headset on your ear:
1
2
3
Open the attached
earhook 45 degrees from
the headset.
Loop the earhook over
Loop the earhook over
your ear.
Press earhook to your ear.
Press earhook to your ear.
When worn, your headset
will look like this on your
head:
1
2
3
To prevent accidental headset operation, slide
the slider lock switch to the locked position.
INDICATOR LIGHTS
With No Charger Plugged In
Headset Indicator
Headset Status
Off
Power off
Three blue flashes
Powering on/off
Steady blue
Pairing mode
Rapid blue/purple flashes Pairing successful
Quick blue flash
Quick blue flash
Incoming/outgoing call
Slow blue pulse
Connected (on a call)
Slow blue flash
Standby (not on a call)
Slow red flash
Idle (not connected
to phone)
Slow purple pulse
Connected call muted
Quick red flash
Low battery
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
flashing to conserve power, but the headset remains on.
With the Charger Plugged In
Headset Indicator
Headset Status
Red
Charging
Yellow
Charging 80% done
Green
Charging complete
MAKING CALLS
CONTINUED