Enterasys csx5500 用户指南
USER’S GUIDE
100 CyberSWITCH
4.
Ensure that the administration console is properly connected to the administration port on the
CyberSWITCH.
CyberSWITCH.
5.
Plug the power cord into a grounded electrical outlet.
6.
Power on the CyberSWITCH by pressing the POWER-ON button.
7.
Power on the administration console PC. After a few seconds, power-on initialization will
begin.
begin.
Initiating a Connection:
1.
1.
Execute Carbon Copy’s cchelp program which invokes Carbon Copy for guest operation.
2.
Select Call CC Device <F1> from displayed menu.
3.
Press <ENTER> or <RET>. (No telephone number is necessary since this is a local connection).
4.
Carbon Copy will present you with a login prompt. Proceed to
.
R
EMOTE
C
ONNECTION
USING
T
ELNET
Telnet is available by default when IP routing is enabled on the CyberSWITCH.
Note: This type connection is not valid for first-time connections to the CyberSWITCH since you
Note: This type connection is not valid for first-time connections to the CyberSWITCH since you
need the CyberSWITCH’s IP address for access. However, it is a viable option for routine
system management and/or data transfer once initial installation and configuration have
been performed.
system management and/or data transfer once initial installation and configuration have
been performed.
To access the CyberSWITCH using Telnet, you must have a Telnet client software package. A
Telnet client software package is built into the CyberSWITCH. With the CyberSWITCH acting as
the Telnet client, simply enter the
Telnet client software package is built into the CyberSWITCH. With the CyberSWITCH acting as
the Telnet client, simply enter the
telnet <ip address>
command to Telnet into the target
host. Refer to the System Commands chapter for a complete listing of available
.
If you are using a PC as a Telnet client, the PC must have a Telnet client software package. From
the Telnet client package, you will access the CyberSWITCH by connecting to the CyberSWITCH’s
IP address.
the Telnet client package, you will access the CyberSWITCH by connecting to the CyberSWITCH’s
IP address.
LAN access:
To access the CyberSWITCH you must set the device’s IP address to be on the same subnet as the
CyberSWITCH. Then place the CyberSWITCH on the LAN and Telnet to the address.
To access the CyberSWITCH you must set the device’s IP address to be on the same subnet as the
CyberSWITCH. Then place the CyberSWITCH on the LAN and Telnet to the address.
WAN access:
1.
1.
Connect the system to the (WAN) ISDN line.
2.
From a remote device that supports unnumbered IP connections, dial in as a PPP CHAP device
USER1 (USER1 as secret). Provide Telnet with the CyberSWITCH address.
USER1 (USER1 as secret). Provide Telnet with the CyberSWITCH address.
3.
From a remote device only supporting numbered IP connections, set up an IP Address 2.2.2. 3
and have it dial as a PPP CHAP device USER2 (USER2 as secret). Provide Telnet with the
CyberSWITCH address of 2.2.2.2.
and have it dial as a PPP CHAP device USER2 (USER2 as secret). Provide Telnet with the
CyberSWITCH address of 2.2.2.2.