TELEDEX plus s 用户指南

Included with the Diamond+S-5/S are (one each):

• Base unit

• Coiled handset cord

• User guide

• Handset

• Clear plastic overlay

• Line cord

Contact your supplier or Teledex for information on ordering

custom designed and printed faceplates to enhance the look of your

Teledex Diamond+S-5/S telephone.

1) Located on the left side of the Diamond is a modular jack

labeled

Insert one end of the coiled handset cord

into this jack. (You should hear the coil cord click when proper-

ly inserted).

2) Insert the other end of the coiled handset cord into the modular

jack on the handset.

3) Turn the telephone so the back panel is facing you. Insert either

end of the line cord into the jack on the back of the telephone

labeled

4) Insert the other end of the line cord into a telephone wall outlet

jack.

5) Once your telephone is connected, place the paper faceplate over

the keys. The plastic overlay slips into place by hooking the tabs

on the overlay into the recessed slots located on both sides. The

overlay is easiest to insert when; the left or right side tabs are

inserted first, and the middle part of the overlay is slightly bowed

to allow for insertion of the other tabs.

1) Lift the handset to connect to the ringing line.

2) To end the call, hang up by replacing the handset.

1) Lift the handset.

2) Listen for dial tone, dial the desired number, or press an 

key to automatically dial a number.

3) To end the call, hang up by replacing the handset.

To increase/decrease Speakerphone volume:

Locate the slide switch (labeled 

) located on the right side of

the telephone.

To increase speaker volume slide the SPKR VOL switch towards the

rear of the telephone. To decrease speaker volume slide the SPKR VOL

switch towards the front of the telephone. 

1) Press the 

key. The red LED will light.

2) Face the phone to talk (The microphone is located on the front

edge of the telephone).

3) To go to the handset mode, lift the handset, press the SPEAKER-

PHONE key (the LED will go out).

1) Press SPEAKERPHONE key. The red light will light.

2) Replace the handset.

3) To end a speakerphone call, press the SPEAKERPHONE key.

1) Without lifting the handset, press the 

key. The

red LED will light indicating an active call.

2) Listen for dial tone dial the desired number, or press an 

key to automatically dial a number.

3) To end speakerphone calls press the SPEAKERPHONE key - the

LED will go out.

1) Without lifting the handset, press the 

key. The

LED will light - you will be on the Speakerphone.

2) To end speakerphone calls press the SPEAKERPHONE key - the

LED will go out.

The Diamond+S-5/S has up to 10 programmable 

keys.

These keys can be programmed to automatically dial telephone num-

bers or activate telephone system features. The Diamond will dial the

stored number each time an AUTO DIAL key is pressed.

The phone must be connected to a telephone line.

1) Lift the handset.

2) Press the 

key and release it.

3) Enter the telephone number including PAUSE* as required.The

dialing sequence can be up to 15 digits.

4) Press the 

key where the number is to be stored.

5) Replace the handset.

1) Press the red 

key. The red HOLD LED will light. The

handset can be replaced without disconnecting the call.

2) To return to the call on HOLD, remove the handset from the

cradle, or press the HOLD key.

The 

key will increase the handset volume.

Pressing this button during a call will increase the receive volume.

Pressing again will return the volume to the normal level. The handset

volume is reset to normal with each new call.

The 

key is a programmable AUTO DIAL key*. Upon

delivery the CALL WAITING key will be programmed with a 600ms.

hookflash.

*Some PBX systems may require 'Flash Plus Digits' to be dialed to access

CALL WAITING. Contact your systems administrator for details.

The FLASH key, when programmed behind an AUTO DIAL key pro-

vides a timed line interrupt typically used for accessing PBX/CO fea-

tures like transfer and conference. The timing of the hookflash is pro-

grammable with the factory default set to 600 millieseconds. Some

PBX's may require you to change the hookflash timing from the

default 600ms.

To change the Hookflash timing:

1) Lift the Handset.

2) Press the 

key (see diagram on back page).

3) Press the 

key (see diagram on back page).

4) Select 1-0 on the DTMF pad. The number selected will be the

new Flash timing in milliseconds (ie: "3" = 300 milliseconds).

5) Press the 

key.

The PAUSE key can be used to provide a timed pause between dialed

digits within an AUTO DIAL key. The timing of the pause is program-

mable with the factory default set to zero (0) seconds. 

To change the Pause timing:

1) Lift the Handset.

2) Press the 

key (see diagram on back page).

3) Press the 

key (see diagram on back page).

4) Select 1 - 9 on the DTMF pad. The number selected will be the

new Pause timing in seconds (ie: "3" = 3 seconds).

5) Press the 

key.

The raised red lens is a Message Waiting light. Some telephone systems

permit an operator or message center to turn on the red Message

Waiting light to alert you that you have a message waiting.

Additionally, the Message Waiting light will act as a visual ring indica-

tor, flashing when the telephone is ringing.

Press the 

key. The red LED below the MUTE key will light.

The party on the other end will not hear you when the MUTE key is

de-pressed.

Pressing the 

key again will deactivate the MUTE key (the

MUTE LED will go out). This will allow you to be heard.

1) Lift the handset, or press the 

key.

2) Press the 

key, the Diamond will dial the last number dialed.