ATTO Technology diamond array v 用户手册
5
ATTO Technology Inc. Diamond Storage Array Installation and Operation Manual
3.0 Installation Instructions
If you are familiar with the Diamond Storage Array, Fibre Channel, SCSI and RAID configurations, you
may set up and configure the array using these instructions. You will find details, illustrations and other
guidance for more involved operations and special cases in the rest of this manual.
may set up and configure the array using these instructions. You will find details, illustrations and other
guidance for more involved operations and special cases in the rest of this manual.
CAUTION
CAUTION
Before configuring the Diamond Storage
Array, ensure that any computer data to be
stored on the array is properly backed up
and verified. The Manufacturer is not
responsible for the loss of any data stored
on the array under any circumstances and
any special, incidental, or consequential
damages that may result thereof.
Array, ensure that any computer data to be
stored on the array is properly backed up
and verified. The Manufacturer is not
responsible for the loss of any data stored
on the array under any circumstances and
any special, incidental, or consequential
damages that may result thereof.
Three major steps are required to set up the
Diamond Storage Array
Diamond Storage Array
1
Physically set up Diamond Storage Array
2
Connect to Ethernet
3
Configure the drives
Step 1: physical setup
1
Make sure the Diamond Storage Array is
mounted properly and has adequate air flow
around it.
mounted properly and has adequate air flow
around it.
2
Insert the appropriate connector into the
interface card in the back of the Diamond
Storage Array.
interface card in the back of the Diamond
Storage Array.
3
Connect the Fibre Channel or SCSI cable from
your host computer system to the connector. To
use ExpressNAV browser-based management
interface and configure your Diamond Storage
Array, you must connect to the Ethernet port.
your host computer system to the connector. To
use ExpressNAV browser-based management
interface and configure your Diamond Storage
Array, you must connect to the Ethernet port.
4
To set up the Ethernet connection: connect a
cross-over cable (for a direct connection to a
PC) or regular network cable from a network
device to the RJ45 Ethernet port on the
Ethernet management card on the front of the
Diamond Storage Array.
cross-over cable (for a direct connection to a
PC) or regular network cable from a network
device to the RJ45 Ethernet port on the
Ethernet management card on the front of the
Diamond Storage Array.
Step 2a: set up the Ethernet connection
The Diamond Storage Array supports service
operations over the RS-232 serial port using
standard terminal emulation software available
with most systems.
The Diamond Storage Array supports service
operations over the RS-232 serial port using
standard terminal emulation software available
with most systems.
1
Connect a DB-9 null modem serial cable
between the port marked RS-232 on the front of
between the port marked RS-232 on the front of
the Diamond Storage Array and the computer’s
serial port. The cable must be no longer than
three meters.
serial port. The cable must be no longer than
three meters.
2
Make sure the power switches on the power
supplies on the rear of the unit are in the Stand-
by position.
supplies on the rear of the unit are in the Stand-
by position.
3
Plug in the power cords to the back of the unit,
then into an appropriate power source (100-240
VAC).
then into an appropriate power source (100-240
VAC).
4
Reboot your host computer system.
5
Press the Stand-by power switch for each
power supply on the Diamond Storage Array to
the ON position.
power supply on the Diamond Storage Array to
the ON position.
6
Upon successful power up and diagnostics, the
unit displays the POST (power up self test)
information.
unit displays the POST (power up self test)
information.
The Diamond is now in Command Line Interface
mode. You may modify the setup of the Diamond
Storage Array using the CLI (refer to
mode. You may modify the setup of the Diamond
Storage Array using the CLI (refer to
CLI: Interface
via ASCII-based Commands
on page 27), but the
easiest method to configure the array is by using
ATTO ExpressNAV software, a graphical user
management interface accessed through a
standard Internet browser. Refer to
ATTO ExpressNAV software, a graphical user
management interface accessed through a
standard Internet browser. Refer to
ATTO
ExpressNAV: Browser-based Interface
on page 23.
Step 2b: connect to Ethernet
If the Diamond Storage Array is attached to a
DHCP server
DHCP server
1
At the Ready prompt after POST (refer to Step
6 above), type set IPDHCP enabled
6 above), type set IPDHCP enabled
2
Type SaveConfiguration Restart
3
At the Ready prompt after POST (see above),
type get IPAddress
type get IPAddress
4
Enter this address into your browser.
5
The ATTO ExpressNAV screen appears. Log in
using the Telnet defaults:
using the Telnet defaults:
Username: Telnet
Password: Diamond
6
Follow the screens to find information about the
array or to configure the array from the factory-
array or to configure the array from the factory-