EchoStar dvr-5000 hdd 软件指南
Section 7
EchoNAV User Interface
Page 7 - 3
©
2
001
E
c
hoS
tar
Inte
rnati
o
nal
C
o
rp
orat
io
n
A
ll
ri
g
hts
re
s
erved
7
5.
TO SOLVE AN INSTALLATION RELATED PROBLEM
Problem
Possible cause
What to do?
1. My television does not
receive any signal from
the receiver (UHF only)
the receiver (UHF only)
■
You did not select the
correct audio/video
channel on your TV.
correct audio/video
channel on your TV.
■
Refer to the user manual
of the TV for instructions.
of the TV for instructions.
■
On the receiver, In the TV
system menu select the
correct channel and PAL
setting.
system menu select the
correct channel and PAL
setting.
■
Use another method to
connect the receiver.
connect the receiver.
2. My television does not
receive any signal from the
receiver
receiver
■
You did not select the
correct A/V channel on
your TV.
correct A/V channel on
your TV.
■
Select the correct A/V
channel on your TV.
channel on your TV.
■
You did not use a correct
SCART cable.
SCART cable.
■
Use only a full featured
SCART cable that is
correctly shielded.
SCART cable that is
correctly shielded.
3. My television shows black
areas on the left and right
of the screen.
of the screen.
■
You did not select the
correct aspect ratio for
your TV.
correct aspect ratio for
your TV.
■
On the receiver, in the user
profile menu select the
correct aspect ratio.
profile menu select the
correct aspect ratio.
4. In a motorized installation,
the dish turns to the West
while I select Set East
Limit.
while I select Set East
Limit.
■
The motor turns the other
way around because the
cable is not installed
correctly.
way around because the
cable is not installed
correctly.
■
At the receiver, change the
cable connections to M1
and M2.
cable connections to M1
and M2.
5. In a motorized installation,
I cannot select a specific
satellite.
satellite.
■
The required satellite is
located outside the
selected East or West
limit.
located outside the
selected East or West
limit.
■
If physically possible, mind
dish damage, revise the
limit setting.
dish damage, revise the
limit setting.
■
Select another satellite.
6. In a motorized installation,
the positioner reacts
unpredictable which
results in incorrect posi-
tioning of the dish.
unpredictable which
results in incorrect posi-
tioning of the dish.
■
The cables used are worn,
damaged or corroded.
damaged or corroded.
■
Inspect the cable for
possible damage and
install new cable as
required.
possible damage and
install new cable as
required.
■
The cable is incorrectly
finished or not sufficiently
shielded.
finished or not sufficiently
shielded.
■
Use sufficiently shielded
and correctly finished
cables.
and correctly finished
cables.
7. During (initial) setup of the
receiver, no channels are
found.
found.
■
You did not select the
correct LNB(F).
correct LNB(F).
■
On the receiver, in the
installation setup menu
select the correct LNB(F).
installation setup menu
select the correct LNB(F).
■
When installed, you have
selected the incorrect
switch type or port.
selected the incorrect
switch type or port.
■
On the receiver, in the
installation setup menu
make the correct
selections.
installation setup menu
make the correct
selections.
■
You have selected the
incorrect satellite to search
channels on.
incorrect satellite to search
channels on.
■
On the receiver, in the
installation setup menu
select the correct satellite.
installation setup menu
select the correct satellite.
■
You have selected the
incorrect search method.
incorrect search method.
■
At an initial setup, always
choose the option All.
choose the option All.