Philips 32PFL3506 用户指南
25
English
Channel list
The channels selected here can be skipped when selecting the channels
using CH + / −.
using CH + / −.
Those channels can still be selected with the Number buttons.
1
Press MENU on the remote control and select [Setup] >
[Channel List].
[Channel List].
Picture
Autoprogram
Sound
Channel List
Setup
Add Channels
Features
Antenna
Language
USB
2
Press
Î or ï to select the channel you want to remove, then
press OK.
Ch Select
Watch/Skip
Back
BACK
OK
40.2
40.3
DTV
DTV
DTV
40.1
Picture
Highlight channels for Ch Up/Down key
selection.
selection.
Sound
Setup
Features
Language
USB
•
The channel display for the removed channel darkens. You will not
be able to select the channel again using CH + / −.
•
To reactivate a removed channel, press
Î or ï and press OK. The
registered channels are highlighted.
•
When you remove a major channel, its minor channels are
removed as well.
Note
•
The channel with the [DTV] indicated on the display is ATSC. Otherwise the channel
is NTSC.
is NTSC.
3
Press MENU to exit.
Add channels
This function lets you add the channels that were not added by the
autoprogram due to the receptible condition at the initial setup.
autoprogram due to the receptible condition at the initial setup.
1
Press MENU on the remote control and [Setup] > [Add Channels].
Picture
Autoprogram
Sound
Channel List
Setup
Add Channels
Features
Antenna
Language
USB
2
Press a number (1 to 135) to enter the number of the channel you
want to add, then press OK.
11
Ch Change
Back
BACK
Picture
For analog channels,
select a channel to be
added using number keys.
select a channel to be
added using number keys.
For digital channels,
you must perform
Autoprogram function.
you must perform
Autoprogram function.
Add channels
Sound
Setup
Features
Language
USB
3
Press MENU to exit.
Note
•
If setup completes successfully, [Added to the channel list] is displayed.
•
If external input is used, it is not possible to register the channel and [Unavailable] will
be displayed on the TV screen.
be displayed on the TV screen.
•
By pressing
Î or ï you can select the memorized channels only.
•
In most cases, digital channels are not broadcast on the RF channel on which they
appear on your TV. To add digital channels you need to know the RF channel on which
the digital channel is being broadcast. E.g. If there is a digital channel 9.1 which is being
broadcast on RF channel 25, you need to enter 25 while performing a weak channel
installation. To fi nd out the RF channel on which a particular digital channel is being
broadcast, please contact your local service provider.
Installing digital channels using [Add channels] might not work for direct cable
connections and if the digital signal is too weak for the TV to process.
appear on your TV. To add digital channels you need to know the RF channel on which
the digital channel is being broadcast. E.g. If there is a digital channel 9.1 which is being
broadcast on RF channel 25, you need to enter 25 while performing a weak channel
installation. To fi nd out the RF channel on which a particular digital channel is being
broadcast, please contact your local service provider.
Installing digital channels using [Add channels] might not work for direct cable
connections and if the digital signal is too weak for the TV to process.
Optimizing the signal quality from your antenna
You can optimize your signal quality by tuning in ATSC channels with
weak signals, and adjusting the antenna.
weak signals, and adjusting the antenna.
1
Press MENU on the remote control and select [Setup] > [Antenna].
2
Press OK to confi rm your choice.
3
Press a number (1 to 135) or press CH + or CH − to select the
channel for which you want to check the digital signal strength.
4
Press MENU to exit.
EN