Garmin 530 用户指南
168
168
12 - messages
abbreviations &
nav terms
User card format unknown — A data card has been inserted, but the format
of the card is not recognized.
User card invalid — A data card has been inserted, but the card has failed
the checksum error test.
User Magnetic Variation in effect — Will appear at power up if “User Mag-
netic Variation” was selected during last use. When “User Magnetic Variation”
is selected, heading references are based on a user-entered setting and WILL
NOT change as you travel large distances.
VLOC has failed — The GNS 530 has detected a failure in its VLOC receiver.
The VLOC receiver is not available and the unit should be returned to your
Garmin dealer for service.
VLOC is not responding — Internal system-to-system communication
between the main pro cessor and the VLOC receiver has failed.
Operational status of the VLOC receiver is unknown and the unit should be
returned to your Garmin dealer for service.
VLOC needs service — The GNS 530 has detected a failure in its VLOC re-
ceiver. The VLOC receiver may still be usable, but the unit should be returned
(at your earliest convenience) to your Garmin dealer for service.
VLOC remote transfer key is stuck — The remote VLOC transfer switch is
of the card is not recognized.
User card invalid — A data card has been inserted, but the card has failed
the checksum error test.
User Magnetic Variation in effect — Will appear at power up if “User Mag-
netic Variation” was selected during last use. When “User Magnetic Variation”
is selected, heading references are based on a user-entered setting and WILL
NOT change as you travel large distances.
VLOC has failed — The GNS 530 has detected a failure in its VLOC receiver.
The VLOC receiver is not available and the unit should be returned to your
Garmin dealer for service.
VLOC is not responding — Internal system-to-system communication
between the main pro cessor and the VLOC receiver has failed.
Operational status of the VLOC receiver is unknown and the unit should be
returned to your Garmin dealer for service.
VLOC needs service — The GNS 530 has detected a failure in its VLOC re-
ceiver. The VLOC receiver may still be usable, but the unit should be returned
(at your earliest convenience) to your Garmin dealer for service.
VLOC remote transfer key is stuck — The remote VLOC transfer switch is
stuck in the enabled (or “pressed”) state. Try pressing the switch again to cycle
its operation. If the message persists, contact your Garmin dealer for assistance.
VLOC transfer key stuck — The VLOC fl ip-fl op key is stuck in the enabled
(or “pressed”) state. Try pressing the VLOC fl ip-fl op key again to cycle its
operation. If the message persists, contact your Garmin dealer for assistance.
Waypoint already exists — The name you have entered for a user waypoint
already exists in memory.
Waypoint(s) have been replaced — One or more user waypoints were up-
dated during a unit-to-unit crossfi ll operation.
Waypoint memory is full — You have used all 1000 user waypoint locations
in the GNS 530’s memory. Delete unwanted waypoints to make room for new
entries.
WGS 84 datum has been selected — The system map datum was changed
to WGS 84 because the selected map datum was removed from the current
NavData® card (database update), the data card is missing or the data card has
failed.
its operation. If the message persists, contact your Garmin dealer for assistance.
VLOC transfer key stuck — The VLOC fl ip-fl op key is stuck in the enabled
(or “pressed”) state. Try pressing the VLOC fl ip-fl op key again to cycle its
operation. If the message persists, contact your Garmin dealer for assistance.
Waypoint already exists — The name you have entered for a user waypoint
already exists in memory.
Waypoint(s) have been replaced — One or more user waypoints were up-
dated during a unit-to-unit crossfi ll operation.
Waypoint memory is full — You have used all 1000 user waypoint locations
in the GNS 530’s memory. Delete unwanted waypoints to make room for new
entries.
WGS 84 datum has been selected — The system map datum was changed
to WGS 84 because the selected map datum was removed from the current
NavData® card (database update), the data card is missing or the data card has
failed.
The following additional annunciator messages may appear in the lower right
corner of the GNS 530’s display:
corner of the GNS 530’s display:
APPROACHING WPT — Approaching waypoint (waypoint alert)
HOLD DIRECT — ”Direct” holding pattern entry
HOLD PARALLEL — ”Parallel” holding pattern entry
HOLD TEARDROP — ”Teardrop” holding pattern entry
NEXT DTK — Waypoint alert. Prepare to turn to the indicated heading upon
waypoint passage.
START PROC TRN — Start Procedure Turn. Reminder message to commence
course reversal maneuver.
TURN TO ###° — Turn advisory. Turn to the indicated heading.
HOLD DIRECT — ”Direct” holding pattern entry
HOLD PARALLEL — ”Parallel” holding pattern entry
HOLD TEARDROP — ”Teardrop” holding pattern entry
NEXT DTK — Waypoint alert. Prepare to turn to the indicated heading upon
waypoint passage.
START PROC TRN — Start Procedure Turn. Reminder message to commence
course reversal maneuver.
TURN TO ###° — Turn advisory. Turn to the indicated heading.
113-188.indd 168
4/11/2003, 9:06:30 AM