Venturer dm8300 用户指南
Total number of tracks
Begin to play the first track
811-830091-012
PRINTED IN CHINA
Pause mode of the 1st track
TROUBLE SHOOTING GUIDE
Should any problem persist after you have made the following checks, consult your nearest service
facility.
facility.
DISC PLAY DOES NOT START:
•
The disc is inserted upside down or incorrectly. Insert the disc correctly with the label surface
up
up
•
Dusty or defective disc
•
Dirty or dusty lens
•
The disc compartment lid is not closed
•
Moisture condensation-> leave the unit in a warm place until the moisture evaporates
•
The AC power adaptor is not plugged into the wall outlet
•
The unit is not placed on a level surface
•
Weak batteries
NO SOUND FROM THE HEADSETS:
•
The headphones / earphones plug is not firmly connected to the “PHONES” jack.
•
Adjust the volume control
•
Dirty plug
NO SOUND FROM THE CONNECTED SPEAKERS:
•
Check the connections
•
The amplifier is not turned on
SKIPPING OF SOUND:
•
Dirty or defective disc
•
Dirty lens
•
Strong vibration
WHEN USING WITH BATTERIES THE BATTERY LIFE IS SHORT:
•
•
Manganese batteries are used. Use alkaline batteries.
DISPLAY WINDOW SHOWS “
” ERROR MESSAGE AND THE UNIT CANNOT BE OPERATED:
•
No disc, dirty or scratched disc. The unit will return to power off after approx. 30 seconds, or
reset the player by pressing “ ” button once and then insert a disc to start playing.
reset the player by pressing “ ” button once and then insert a disc to start playing.
SPECIFICATIONS
GENERAL
OUTPUT (at 1KHz 0dB level): Headphones / earphones (stereo mini-jack)
15 mW+15mW at 16 Ohms to 32 Ohms
POWER REQUIREMENTS:
3V (2 x AA / LR6 / MN 1500) alkalline batteries,or
DC IN 6V, 350mA power adaptor
Polarity of plug
DC IN 6V, 350mA power adaptor
Polarity of plug
DIMENSIONS:
Approx. 140 X 27 X 162 mm (W/H/D)
OPERATING VOLTAGE:
We continually strive to improve our products, specifications may change without notice.
DISC PLAYING
1. Open the CD door by pressing the OPEN button.
2. Place a CD with the label side facing upwards onto the centre spindle, gently push down until
2. Place a CD with the label side facing upwards onto the centre spindle, gently push down until
the disc clicks in place.
3. Press the top of the CD lid to close.
ON DISPLAY WINDOWS
If a CD is loaded, when you press “
” button, the display window shows:
DURING PLAYING
The track number of the current selection appears.
When “ ” is pressed during play, total number of tracks on the disc will be displayed and the unit
will stop playing.
If “ ” is pressed again the unit will be returned to full stop mode. If “
When “ ” is pressed during play, total number of tracks on the disc will be displayed and the unit
will stop playing.
If “ ” is pressed again the unit will be returned to full stop mode. If “
” is pressed the unit
returns to play mode.
Note: When the STOP button has been pressed once during play, if another button is not pressed
within 30 seconds, then the unit will be placed in full stop mode.
Note: When the STOP button has been pressed once during play, if another button is not pressed
within 30 seconds, then the unit will be placed in full stop mode.
DURING PAUSE
The playing track number will flash.
When no disc is inserted and “
” button is pressed, “
” will be shown in the display.
The unit cannot be operated when error message is displayed. After approx. 30 seconds the unit
will return to full stop mode. Reset the player by pressing “ ”once and then insert a disc to start
playing.
will return to full stop mode. Reset the player by pressing “ ”once and then insert a disc to start
playing.
VARIOUS PLAYING MODES
During playback, every time the “ PLAY MODE ” button is pressed, the playing mode will be
changed as follows:
changed as follows:
IN NORMAL PLAYING MODE:
NORMAL PLAY -> (
) REPEAT ONE -> (
) REPEAT ALL -> INTRO -> SHUFFLE
NORMAL PLAY-- Playing the whole disc
The CD is played once from the beginning to the end.
REPEAT PLAYBACK-- Repeat One and Repeat All
•
To repeat single track
Press “ PLAY MODE ” button during play until “
” appears in the
display. The selected track will be played repeatedly.
To select another track, press “
”or “
” button.
•
To repeat whole disc
Press “ PLAY MODE ” button during play until “
” appears in the
display.
The whole disc will be played repeatedly.
The whole disc will be played repeatedly.
INTRO PLAY-- Playing the first ten seconds of all the tracks
1. Press “ PLAY MODE ” button during play until “ INTRO ” flashes in the
display.
2. Press “
” button to begin “ INTRO ” play.
Each track will be played about ten seconds.
3. Pressing “
” button again will cease intro play and continue to normal
playback.
NOTE: Intro play always starts from the first track.
Middle East and Australia:
240V AC ±5% 50Hz
240V AC ±5% 50Hz
UK and Germany
230V AC ±5% 50 Hz
230V AC ±5% 50 Hz
Chile:
230V AC ±5% 50 Hz
230V AC ±5% 50 Hz
Singapore, Malaysia & Thailand
200-240V AC ±5% 50 Hz
200-240V AC ±5% 50 Hz
Japan
100V AC ±5% 50/60 Hz
100V AC ±5% 50/60 Hz
U.S.A., Canada:
120V AC ±5% 60Hz
Output (at 1 KHz 0 dB level)
120V AC ±5% 60Hz
Output (at 1 KHz 0 dB level)
SHUFFLE PLAY--playing the tracks in random order
1. Press “ PLAY MODE ” button during play until “ SHUFF ” flashes
in the display.
2. Press “ PLAY/PAUSE ” button to begin the shuffle play.
•
To locate the next track, press “
” button.
NOTE: You cannot locate the previous track even you keep the “
” button
pressed.
PROGRAM PLAY--playing the tracks in the desired order
1. Press “ PROGRAM ” button until “ PROG ” and “
01
” flash in the
display.
2. Press “
” or “
” button to select the desired track.
3. Press “ PROGRAM ” button to register track no. 6, for example,
as the first selection. The program number indication will be
changed to the next one, for example: “
changed to the next one, for example: “
02
”.
4. Repeat steps 2 to 3, until all the desired tracks are programmed
(up to 24 tracks).
5. Press “
” button, and program playing begins.
NOTES:
•
•
Repeat play and intro play can be performed during program play. But shuffle play is inactive.
•
The program is erased, when:
1. The disc compartment is opened or the auto power off function turns the power off.
2. If the program mode is exited by one press of the “ ” button, all the program will still
1. The disc compartment is opened or the auto power off function turns the power off.
2. If the program mode is exited by one press of the “ ” button, all the program will still
remain in memory.
3. If the “ ” button is pressed a second time then the stored program will be erased.
•
The program still remain in the memory when “ ” button is pressed.
PROGRAM EDITION
To add:
To add:
To add additional tracks to your selection during program playback, press “ ” button
first and then press “ PROGRAM ” button repeatedly until “
first and then press “ PROGRAM ” button repeatedly until “
00
” flashes in the display.
Repeat the above step 2 and 3 to store additional tracks.
To check:
Press “ PROGRAM ” button lightly during programming before you press “
” button.
Each time “ PROGRAM ” button is pressed the program number appears in the display
window.
window.
To change: When checking press either skip button to alter the track number for the program
currently displayed. Press “ PROGRAM ” button to register the newly selected track
into memory.
into memory.
To delete: Opening the CD door will result in any Programmed memory being deleted.
MAINTENANCE
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
CLEANING A CD
If the CD skips or will not play, the disc may need to be cleaned.
Before playing, wipe the disc from its centre to its outer edge with a soft cleaning cloth. After
playing, store the disc in its case.
Before playing, wipe the disc from its centre to its outer edge with a soft cleaning cloth. After
playing, store the disc in its case.
HANDLING THE DISC
Only touch the CD on the edge to avoid finger prints on its surface.
Do not stick paper or tape nor write anything on the surface of the CD.
Do not stick paper or tape nor write anything on the surface of the CD.