Hitachi deskstar 4 安装指导
IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 3.0
Attaching the drive
1. Turn off the computer, unplug the power cord, and
open the case.
2. Match pin 1 of the 40-pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.
3. Attach a power plug to either the 3- or 4-pin power
connector.
1. Turn off the computer, unplug the power cord, and
open the case.
2. Match pin 1 of the 40-pin cable to pin 1 of the drive
interface connector. Pin 1 is usually denoted by a
stripe along the edge of the cable.
3. Attach a power plug to either the 3- or 4-pin power
connector.
Mounting the drive
1. Mount the drive securely, using the appropriate
1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in either bottom or side mounting
holes.
metric screws in either bottom or side mounting
holes.
2. The maximum screw insertion depth for the bottom
mounting is 4 mm and for side mounting 4.5 mm.
Configuring your computer
1. If your computer has a plug-in IDE card with a drive
installation procedure, follow the manufacturer’s
instructions.
2. Plug in the power cord and power on your
computer. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen. If so, proceed to step 4.
3. If your computer does not prompt you to recon-
figure, enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your computer’s
documentation for the proper key sequence. If the
computer fails to boot up, power off, remove the new
hard drive and return your system to its original con-
figuration. Reboot and enter your computer’s Setup.
Follow the directions in step 4, then reattach the new
hard drive.
4. Select “Auto Detect” if your computer Setup sup-
ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.
1. If your computer has a plug-in IDE card with a drive
installation procedure, follow the manufacturer’s
instructions.
2. Plug in the power cord and power on your
computer. Your computer may detect a configuration
change and prompt you to proceed to the Setup
screen. If so, proceed to step 4.
3. If your computer does not prompt you to recon-
figure, enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your computer’s
documentation for the proper key sequence. If the
computer fails to boot up, power off, remove the new
hard drive and return your system to its original con-
figuration. Reboot and enter your computer’s Setup.
Follow the directions in step 4, then reattach the new
hard drive.
4. Select “Auto Detect” if your computer Setup sup-
ports this feature. If your computer does not Auto
Detect the drive, select the appropriate UDT (User
Definable Type) for the model being installed.
Then run Disk Manager.
4330MB
63
16
8,400
DCAA-34330
3610MB
63
16
7,000
DCAA-33610
2880MB
63
16
5,600
DCAA-32880
Cap.
Sector
/Track
Heads
Cylinders
IBM model
number
Running Disk Manager
1. Insert the Ontrack diskette and reboot your com-
puter.
2. Type DM and press [ENTER] to run Disk Manager.
3. Under “Select an Installation Option” select (E)asy
Disk Installation.
4. Select a drive for installation; Disk Manager will
partition and format the drive.
5. A status dialog will indicate a successful
installation.
1. Insert the Ontrack diskette and reboot your com-
puter.
2. Type DM and press [ENTER] to run Disk Manager.
3. Under “Select an Installation Option” select (E)asy
Disk Installation.
4. Select a drive for installation; Disk Manager will
partition and format the drive.
5. A status dialog will indicate a successful
installation.
If, after complete installation, your system will not
boot up, recheck all settings. If the system still fails to
boot up, remove the new drive from your system to
boot up, recheck all settings. If the system still fails to
boot up, remove the new drive from your system to
return to your original configuration and contact
technical support.
technical support.
®
© International Business Machines Corporation 1999
www.ibm.com/harddrive
IBM Hard Disk Drive Technical Support Center
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.426.5214 or 507.286.5825
Fax: 507.253.DRIVE
E-mail: drive@us.ibm.com
Rochester, MN 55901
Telephone: 888.426.5214 or 507.286.5825
Fax: 507.253.DRIVE
E-mail: drive@us.ibm.com
Singapore Technical Support Center
Telephone: (65)6418.9595 or 1800.418.9595
E-mail: drive@sg.ibm.com
Telephone: (65)6418.9595 or 1800.418.9595
E-mail: drive@sg.ibm.com
IBM Systems Storage Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
Printed in the United States of America
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DCAA 32880/33610/34330, revision 1.0
Product Description data represents IBM’s design objectives and is provided for com-
parative purposes; actual results may vary based on a variety of factors. This product data
does not constitute a warranty. Questions regarding IBM’s warranty terms or methodology
used to derive this data should be referred to the IBM Hard Disk Drive Technical Support
Center. Data subject to change without notice.
parative purposes; actual results may vary based on a variety of factors. This product data
does not constitute a warranty. Questions regarding IBM’s warranty terms or methodology
used to derive this data should be referred to the IBM Hard Disk Drive Technical Support
Center. Data subject to change without notice.
Date: 11 January 1999