Hitachi deskstar 8 安装指导
Quick installation guide
Deskstar 8
AT/IDE
Models: DHEA-34331, DHEA-36481,
DHEA-38451
IBM storage products
Page 1
IBM Hard Disk Drive Technical Support Center version 3.1
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of
breather hole may result in loss of
data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it
in the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it
in the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
Quick installation procedure
Note: It is advisable to backup all data before
proceeding with the installation.
proceeding with the installation.
If your system BIOS cannot handle large capacity
drives (over 540 MB), you may need to use a disk
overlay program such as Ontrack’s Disk Manager.
The following procedure uses the Ontrack Disk
Manager software. Information on obtaining a copy of
Ontrack’s Disk Manager can be found on the Web at
www.ibm.com/harddrive.
drives (over 540 MB), you may need to use a disk
overlay program such as Ontrack’s Disk Manager.
The following procedure uses the Ontrack Disk
Manager software. Information on obtaining a copy of
Ontrack’s Disk Manager can be found on the Web at
www.ibm.com/harddrive.
Setting the jumpers
1. Refer to your computer manual to determine if you
require the 15 or 16 head logical architecture.
2. In a one drive system, configure your new drive as
Master (Device 0) with no jumpers installed.
3. In a two drive system, one drive must be desig-
nated as the Master, the other as the Slave (Device 1)
4. When installing the new drive as a Slave, check
the Master drive to determine if a jumper change is re-
quired to indicate the presence of a Slave drive.
5. Consult your manual to see if your computer sup-
ports Cable Select before choosing this option.
1. Refer to your computer manual to determine if you
require the 15 or 16 head logical architecture.
2. In a one drive system, configure your new drive as
Master (Device 0) with no jumpers installed.
3. In a two drive system, one drive must be desig-
nated as the Master, the other as the Slave (Device 1)
4. When installing the new drive as a Slave, check
the Master drive to determine if a jumper change is re-
quired to indicate the presence of a Slave drive.
5. Consult your manual to see if your computer sup-
ports Cable Select before choosing this option.
16 head logical architecture
Jumper pins
Master A-B and G-H
Slave A-B and C-D
Cable Select E-F and A-B
Slave Present E-F & G-H
Jumper pins
Master A-B and G-H
Slave A-B and C-D
Cable Select E-F and A-B
Slave Present E-F & G-H
15 head logical architecture
Jumper pins
Master A-C and G-H
Slave A-C
Cable Select A-C and E-F
Jumper pins
Master A-C and G-H
Slave A-C
Cable Select A-C and E-F
Slave Present A-C, E-F &
GH
39 19 1 I G E C A
40 20 2 H F D B