Hitachi 1gb 安装指导
IBM storage products
Page 1
IBM Technology Group Support Center
version 1.1
Ibm
Quick installation guide
IBM Microdrive
™
CF+ Type II
Models: DSCM-11000
DSCM-10512
DSCM-10340
DSCM-10340
Handling precautions
•
Follow these suggestions to optimize the use of
your IBM Microdrive, as well as those devices
in which it is installed:
your IBM Microdrive, as well as those devices
in which it is installed:
•
Do not seal the breather hole! Sealing the
breather hole may result in loss of data.
breather hole may result in loss of data.
•
Do not press on the drive! Do not apply any
force to the drive during handling or installation.
force to the drive during handling or installation.
•
Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).
damage from shock, vibration, or electrostatic
discharge (ESD).
•
Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
touch any exposed printed circuit board.
•
Do not write on the label or remove it. Do not
apply additional labels.
apply additional labels.
•
Always carry the drive in its plastic case.
•
Do not drop the drive.
•
Do not expose the drive to wet conditions.
•
Do not place the drive near a strong magnetic
field.
field.
•
Do not expose the drive to extreme tempera-
tures.
tures.
•
Do not use the drive in CF+
TM
Type II slots
without an ejection mechanism.
•
The Microdrive may become hot during opera-
tion. Be careful when removing the drive from
the host device immediately after operation.
tion. Be careful when removing the drive from
the host device immediately after operation.
Quick installation procedure
Note: Back up all data before beginning installation!
Refer to the manual that came with your computer,
camera, or other device to determine if it is compatible
with the CF+ Type II or the PC card type II drive/inter-
face adapter and to find instructions on inserting and
removing the IBM microdrive.
camera, or other device to determine if it is compatible
with the CF+ Type II or the PC card type II drive/inter-
face adapter and to find instructions on inserting and
removing the IBM microdrive.
Ÿ
Using the IBM Microdrive with a PC card adapter
With a PC card adapter the IBM Microdrive can be
installed in devices such as digital cameras or PCs that
have a PC card type II slot. If your Microdrive did not
come with a PC card, it can be purchased separately.
installed in devices such as digital cameras or PCs that
have a PC card type II slot. If your Microdrive did not
come with a PC card, it can be purchased separately.
With both facing upward (the arrow at the upper left
corner of the Microdrive), slide the IBM Microdrive firmly
along the track into the PC card adapter. [If either is not
facing upward, the Microdrive will not fit into the track.]
corner of the Microdrive), slide the IBM Microdrive firmly
along the track into the PC card adapter. [If either is not
facing upward, the Microdrive will not fit into the track.]
Note: When inserting or removing the PC card, hold the
PC card, not the IBM Microdrive.
PC card, not the IBM Microdrive.
Ÿ
Using the IBM Microdrive without a PC card adapter
The IBM Microdrive is compatible with the CF+ Type II
standard and can be used in devices with the CF+ Type
II slot without a card adapter. Refer to the manual
shipped with the device to determine its slot type.
standard and can be used in devices with the CF+ Type
II slot without a card adapter. Refer to the manual
shipped with the device to determine its slot type.
If your PC does not recognize the IBM Microdrive
With the Plug & Play feature of Windows® 98 and 95
your PC should automatically recognize the IBM
Microdrive. If it does not do so, do the following:
With the Plug & Play feature of Windows® 98 and 95
your PC should automatically recognize the IBM
Microdrive. If it does not do so, do the following:
1. In Windows select Start and Settings.
2. Click Control Panel.
3. Click the Hardware icon, click Next.
4. Select No in the Hardware Wizard, click Next.
5. Select Hard disk controller as the hardware type,
click Next.
6. Specify Standard IDE/ESDI hard disk controller
2. Click Control Panel.
3. Click the Hardware icon, click Next.
4. Select No in the Hardware Wizard, click Next.
5. Select Hard disk controller as the hardware type,
click Next.
6. Specify Standard IDE/ESDI hard disk controller