Hitachi 10k300 安装指导
H
H
i
i
t
t
a
a
c
c
h
h
i
i
G
G
l
l
o
o
b
b
a
a
l
l
S
S
t
t
o
o
r
r
a
a
g
g
e
e
T
T
e
e
c
c
h
h
n
n
o
o
l
l
o
o
g
g
i
i
e
e
s
s
Q
Q
u
u
i
i
c
c
k
k
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
H
H
i
i
t
t
a
a
c
c
h
h
i
i
U
U
l
l
t
t
r
r
a
a
s
s
t
t
a
a
r
r
1
1
0
0
K
K
3
3
0
0
0
0
M
M
o
o
d
d
e
e
l
l
s
s
:
:
H
H
U
U
S
S
1
1
0
0
3
3
0
0
3
3
0
0
F
F
L
L
3
3
6
6
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
3
3
0
0
F
F
L
L
3
3
8
8
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
1
1
4
4
F
F
L
L
3
3
6
6
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
1
1
4
4
F
F
L
L
3
3
8
8
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
7
7
3
3
F
F
L
L
3
3
6
6
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
7
7
3
3
F
F
L
L
3
3
8
8
0
0
0
0
_________________________________
Handling precautions
• Do not open the electrostatic discharge
(ESD) bag containing the drive until
required.
required.
• Do not apply pressure on the drive during
handling and installation.
• To prevent damage from impact or vibration
always set the drive down gently.
• Handle the drive carefully by the edges. Do
not touch the exposed printed circuit board
or any electronic components.
or any electronic components.
• Do not cover the breather hole! Covering the
breather hole may result in loss of data.
• Save the packaging materials including the
ESD bag in the event that the drive must be
returned.
returned.
Installing the drive
1. Record the serial number and part number
of your hard drive for future reference
.
2. Turn off the computer and remove the
2. Turn off the computer and remove the
computer system cover
.
3. Before handling the hard disk drive,
3. Before handling the hard disk drive,
discharge any static electricity from yourself
and your clothing. With one hand touch an
unpainted metal surface on the computer
chassis, and then touch the ESD bag with
the other hand for a minimum of two
seconds.
and your clothing. With one hand touch an
unpainted metal surface on the computer
chassis, and then touch the ESD bag with
the other hand for a minimum of two
seconds.
4. Remove the hard drive from the ESD bag.
5. Unplug the computer.
6. Assign a SCSI address if necessary.
6. Assign a SCSI address if necessary.
______________________________________
Wide LVD 68pin-16bits (NW)
Option Jumper Connector (C3)
Pin
No
No
Signal Name
Pin
No.
No.
Signal Name
1
ID3
2
GND
3
ID2
4
GND
5
ID1
6
GND
7
ID0
8
GND
9
Disable Auto
Start
Start
10
GND
11
Force Single
Ended mode
Ended mode
12
GND
13
Enable
Delayed Start
Delayed Start
14
GND
15 Write
Protect
16 GND
17 Reserved
18 GND
19 Reserved
20 GND
21
LED(with 0
ohm)
ohm)
22
5Vwith 150
ohm
ohm
22
Term. Power
to SCSI bus
to SCSI bus
24
Term Power
to SCSI bus
to SCSI bus
Note: The SCSI ID setting is to be set via the eC3
connector (not by the C4.) In case the SCSI ID
setting is done by remote switch via the C4
connector and remote cable, remove all Jumper
Sockets from the C3 connector to avoid ID
control conflicts.
connector (not by the C4.) In case the SCSI ID
setting is done by remote switch via the C4
connector and remote cable, remove all Jumper
Sockets from the C3 connector to avoid ID
control conflicts.
Page 1
version 1.0