Hitachi 18xp 安装指导
Quick installation guide
Ultrastar 9LP
& 18XP
Multi-mode SE/LVD
Models: DGHS-09V, DGHS-09D,
DGHS-18V, DGHS-18D
IBM storage products
Page 1
IBM Hard Disk Drive Technical Support Center version 2.0
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of
breather hole may result in loss of
data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
damage from shock, vibration, or electrostatic dis-
charge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove the
cover.
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
Quick installation procedure
Note: It is advisable to backup all data before pro-
ceeding with the installation.
ceeding with the installation.
This procedure may require use of a bootable System
Diskette containing FDISK.COM and FORMAT.COM.
Diskette containing FDISK.COM and FORMAT.COM.
Setting the address
1. Each drive on the SCSI bus must have a unique
address. Sixty-eight and eighty-pin (Wide SCSI)
devices have 16 possible addresses.
2. SCSI address bits 3 (68- & 80-pin models only), 2,
1, and 0 of the 32-pin Option Jumper Block are used
to select the SCSI device ID.
1. Each drive on the SCSI bus must have a unique
address. Sixty-eight and eighty-pin (Wide SCSI)
devices have 16 possible addresses.
2. SCSI address bits 3 (68- & 80-pin models only), 2,
1, and 0 of the 32-pin Option Jumper Block are used
to select the SCSI device ID.
::::::
SCSI Pin 1
Aux Connector Pin 1
Power Pin 1
Pin 35
Pin 2
1
2
3
4
5
6
7
8 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
2
SCSI Address Bit
3 2 1 0
Blank
Auto
Start
Start
GND
Reserved
External
Activity LED
Activity LED
Write
Protect
Protect
Autostart
Delay
Delay
Force Single
Ended Mode
Ended Mode
Disable Wide Negotiations
Disable Unit
Attention
Attention
Disable SCSI
Parity
Parity
Disable Sync
Negotiations
Negotiations
Reserved
Reserved
GND
GND
+5V
Termination
Power Enable
Power Enable
Reserved