Hitachi 9es 安装指导
IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 3.0
Note: In the table below, “off” means a jumper is not
in place and “on” means a jumper is in place.
in place and “on” means a jumper is in place.
15
on
on
on
on
14
off
on
on
on
13
on
off
on
on
12
off
off
on
on
11
on
on
off
on
10
off
on
off
on
9
on
off
off
on
8
off
off
off
on
7
on
on
on
off
6*
off
on
on
off
5
on
off
on
off
4
off
off
on
off
3
on
on
off
off
2
off
on
off
off
1
on
off
off
off
0
off
off
off
off
Address
Bit 0
Bit 1
Bit 2
Bit 3
* Shipping Default
Attaching the drive
1. Turn off the computer, unplug the power cord, and
open the case.
2. The DDRS drive requires Active Termination on
both ends of the SCSI cable (the SCSI controller
normally provides internal termination for one end of
the cable). If the DDRS drive is the only device on the
SCSI cable, attach it to the end of the 68 pin cable
furthest from the controller and enable termination by
placing a jumper on position 6 of the Option Jumper
Block. If the drive is attached to a cable that contains
other devices and the new drive is not attached to the
end of the cable, jumper position 6 must be open and
Active Termination must be supplied by the device at
the end of the cable.
3. Select the other option jumpers as required by your
computer.
4. Attach the power connector.
1. Turn off the computer, unplug the power cord, and
open the case.
2. The DDRS drive requires Active Termination on
both ends of the SCSI cable (the SCSI controller
normally provides internal termination for one end of
the cable). If the DDRS drive is the only device on the
SCSI cable, attach it to the end of the 68 pin cable
furthest from the controller and enable termination by
placing a jumper on position 6 of the Option Jumper
Block. If the drive is attached to a cable that contains
other devices and the new drive is not attached to the
end of the cable, jumper position 6 must be open and
Active Termination must be supplied by the device at
the end of the cable.
3. Select the other option jumpers as required by your
computer.
4. Attach the power connector.
Mounting the drive
1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in the bottom or side mounting holes.
2. The maximum screw insertion depth for bottom
mounting is 6.0 mm (.23 in) and for side mounting is
3.5 mm (.14 in).
1. Mount the drive securely, using the appropriate
brackets or rails, in any axes, using four 6-32 UNC
metric screws in the bottom or side mounting holes.
2. The maximum screw insertion depth for bottom
mounting is 6.0 mm (.23 in) and for side mounting is
3.5 mm (.14 in).
Configuring your computer
1. Plug in the power cord and power on your com-
puter. Consult your SCSI adapter users guide for
information on configuring a new hard disk drive.
2. Follow the Operating System instructions to format
and partition your drive.
1. Plug in the power cord and power on your com-
puter. Consult your SCSI adapter users guide for
information on configuring a new hard disk drive.
2. Follow the Operating System instructions to format
and partition your drive.
If your system will not boot up after complete
installation, recheck all settings. If the system still
fails to boot up, remove the new drive to return the
system to its original configuration and call the IBM
Hard Disk Drive Technical Support Center.
installation, recheck all settings. If the system still
fails to boot up, remove the new drive to return the
system to its original configuration and call the IBM
Hard Disk Drive Technical Support Center.
© International Business Machines Corporation 1999
www.ibm.com/harddrive
IBM Hard Disk Drive Technical Support Center
Dept. D8M
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.253.4110
Fax: 507.253.DRIVE
E-mail: drive@us.ibm.com
Dept. D8M
3605 Highway 52 North
Rochester, MN 55901
Telephone: 888.IBM.5214 or 507.253.4110
Fax: 507.253.DRIVE
E-mail: drive@us.ibm.com
Singapore Technical Support Center
Telephone: 65.840.9292
E-mail: drive@sg.ibm.com
Telephone: 65.840.9292
E-mail: drive@sg.ibm.com
IBM Systems Storage Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage
Asia-Pacific Headquarters: 65.320.1234
European Headquarters: 44.01.705.561.871
Japan Sales Branch Office: 81.46645.1039
Printed in the United States of America
01-99
01-99
All Rights Reserved
IBM is the registered trademark of International Business Machines Corporation.
Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Hard Disk Drive Technical Support Center.
OEM Hard Disk Drive Specifications for DDRS-39130 / DDRS-34560 (Revision 2.0)
Product Description data represents IBM’s design objectives and is provided for com-
parative purposes; actual results may vary based on a variety of factors. This product data
does not constitute a warranty. Questions regarding IBM’s warranty terms or method-
ology used to derive this data should be referred to the IBM Hard Disk Drive Technical
Support Center. Data subject to change without notice.
parative purposes; actual results may vary based on a variety of factors. This product data
does not constitute a warranty. Questions regarding IBM’s warranty terms or method-
ology used to derive this data should be referred to the IBM Hard Disk Drive Technical
Support Center. Data subject to change without notice.
Date: 6 January 1999
®