Canon D661 安装指导
F o r i n s t a l l a t i o n h e l p a n d o p e r a t i o n a l
i n s t r u c t i o n s , c a l l :
1-800-828-4040 1-800 OK CANON
U.S.A. CUSTOMERS CANADA CUSTOMERS
Output Tray
L50 Cartridge
Label
Connect the supplied power cord to the power
cord connector on the left side of the machine.
cord connector on the left side of the machine.
REMOVE ALL ITEMS FROM THE BOX
CONNECTING USING PARALLEL CABLE
or CONNECTING USING USB CABLE
CONNECTING THE POWER CORD
•
POWER CORD
•
TELEPHONE LINE*
•
DOCUMENTATION
(Set-up Instructions, Reference Guide, Fax Guide*,
Limited Warranty Card, Registration Card)
•
DESTINATION LABEL*
•
CD-ROM
Remove the shipping
attachment on the left
side using a coin.
attachment on the left
side using a coin.
Otherwise the scanning
unit of the machine is
locked and you cannot
make copies or send faxes.
unit of the machine is
locked and you cannot
make copies or send faxes.
Grasp the cartridge
with one hand, firmly
and slowly pull the
sealing tape tab with
the other hand.
with one hand, firmly
and slowly pull the
sealing tape tab with
the other hand.
Remove the
sealing tape
completely.
sealing tape
completely.
Slide left until the
|<
mark appears.
When the power cord is
plugged into the machine
and into the wall outlet,
the machine is turned
on. The LCD displays
PLEASE WAIT. Please
wait until the LCD
returns to the Copy
Mode standby display.
plugged into the machine
and into the wall outlet,
the machine is turned
on. The LCD displays
PLEASE WAIT. Please
wait until the LCD
returns to the Copy
Mode standby display.
Connect the supplied power cord to the power cord
connector on the left side of the machine.
Then connect the other end into a properly grounded 120 VAC three-prong outlet.
connector on the left side of the machine.
Then connect the other end into a properly grounded 120 VAC three-prong outlet.
Copy Mode standby display
Remove the
new cartridge
from its bag.
new cartridge
from its bag.
Insert the removed
shipping attachment
in the holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE
shipping attachment
in the holder.
Keeping the cartridge
cover open, go
to section 2 -
INSTALL CARTRIDGE
Keep the shipping
attachment in the holder
in case you need to
transport the machine.
attachment in the holder
in case you need to
transport the machine.
REMOVE ALL SHIPPING MATERIALS
UNPACK MACHINE
1
INSTALL CARTRIDGE
2
CONNECTIONS
4
S E T - U P I N S T R U C T I O N S
imageCLASS D600 Series
Place the cartridge
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
on a flat and stable
surface, grip the
sealing tape tab
and snap in the
direction shown.
Make sure that the
tab is detached from
the cartridge.
Machine
Rock the cartridge
5 or 6 times to
distribute the
toner evenly.
5 or 6 times to
distribute the
toner evenly.
*D680 Model
Pub. NO. FA7-3911-010
Printed in Thailand
Printed in Thailand
Position the arrow mark
on the cartridge towards
the inside of the machine,
and gently slide the
cartridge in the machine
as far as it will go.
on the cartridge towards
the inside of the machine,
and gently slide the
cartridge in the machine
as far as it will go.
Close the cartridge cover
and slide the platen unit
to the original position.
and slide the platen unit
to the original position.
2
1
1
Lift the platen unit
lever
lever
(1)
and slide
the platen unit
(2)
Open the
cartridge cover.
cartridge cover.
A
E
B
A
B
C
D
E
F
C
D
Grip the cassette
handle, and pull
out towards you
until the cassette
comes to a stop.
handle, and pull
out towards you
until the cassette
comes to a stop.
Load the paper stack beneath
the cassette’s length guide
the cassette’s length guide
(1)
and width guide’s claws
(2).
Make sure that the paper stack does
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
not exceed the length and width
guide’s claws in the cassette. Failure
to do so will cause a paper jam.
Gently insert the cassette as
far as it will go.
far as it will go.
Hook the tab on
the output tray
onto the opening
on the machine.
the output tray
onto the opening
on the machine.
LOAD PAPER
3
A
B
C
PAR
USB interface connection
Connect to your computer using USB cable.
Connect to your computer using USB cable.
USB interface connection.
PARALLEL
Parallel interface connection
Connect to your computer using parallel cable.
Fix the connector solidly using the wire clips.
Fix the connector solidly using the wire clips.
Parallel interface connection
Connect to your computer using parallel cable.
Make sure the computer is turned off.