Canon mp520 快速安装指南
Start Here
Easy Setup Instructions
Loading Paper
This machine offers two paper sources to load
printing paper; the Rear Tray, found at the top
of the machine, and the Front Tray, found at
the front of the machine.
Note
At purchase, the machine is set to feed from
the Rear Tray.
You can load A4, Letter, or B5-sized plain
paper in the Front Tray. When using any other
type of paper, load it in the Rear Tray.
For loading paper in the Front Tray, refer to
“Loading Paper” in the Quick Start Guide.
Rear Tray
Front Tray
Loading Paper in the Rear Tray
a
Load the paper in the Rear Tray
with the print side facing UP.
b
Align the paper stack against the
Cover Guide on the right side of
the Paper Support.
c
Pinch the Paper Guide and slide
it against the left side of the paper
stack.
Cover Guide
Paper Guide
Print side facing UP.
•
•
•
Photo All-In-One
Unpack the Machine
Please confi rm the included items against the illustration printed on the lid of the packing box.
A USB cable is necessary to connect the machine with your computer.
•
•
Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Machine” in the Quick Start Guide.
a
Place the machine on a fl at and
horizontal surface, and do not place
any objects in front of the machine.
Open the Sheet Feeder Cover and pull
out the Paper Support, and then open
the Front Tray and extend the Output
Paper Support.
Caution
Before turning on the machine, remove all the
shipping tapes and protective material on the out-
side of the machine. Then open the Front Tray.
b
Plug the power cord in the back of the
machine and connect the other end to
the wall outlet.
Document Cover
Important
• Plug the power cord all the way in, since it may
be difficult to plug.
• Make sure that the Document Cover is closed.
• Do NOT connect the USB cable at this stage.
c
Open the Operation Panel, then press
the
ON/OFF button to turn on the
machine.
The machine will initialize. Wait until the
Power
lamp stops fl ashing and remains lit green.
1
Prepare the Machine
d
Use the { or } button on the
Operation Panel to select the language
for the LCD, then press the
OK button.
(1) Press the { or }
button to select the
language.
(2) Press the
OK
button.
Important
If an unintended language is displayed on the
LCD, press the Back button on the Operation
Panel to return to the Language selection screen.
Once the message “
Install the print head and
set the ink tank.” appears, go to
e
.
e
Lift the Scanning Unit (Printer Cover)
open, and set the Scanning Unit
Support to hold the cover. The Print
Head Holder moves to the center.
Scanning Unit (Printer Cover)
Scanning Unit Support
f
Write down the serial number located
inside the machine. You will need this
to register your product.
Serial Number Location
3
Install the Ink Tanks
2
Install the Print Head
a
Remove the Print Head from its
package.
Caution
There may be some transparent or light blue ink
on the inside of the bag the print head comes in,
or the inside of the protective cap - this has no
effect on print quality. Be careful not to get ink on
yourself when handling these items.
b
Remove the orange protective cap from
the Print Head and discard it.
Protective Cap
Print Head Nozzles
Electrical Contacts
Note
Do not touch the print head nozzles and the electrical
contacts.
contacts.
c
Firmly raise the Print Head Lock Lever
until it stops. The Print Head Lock
Lever may feel heavy.
d
Insert the Print Head.
Do not touch!
e
Push the Print Head to hold it in place,
and lower the Print Head Lock Lever
carefully.
Note
For the ink tanks compatible with this machine, refer to
the back cover of the Quick Start Guide.
a
Pull the orange tape in the direction of
the arrow to peel off the protective fi lm
and remove the fi lm completely.
If the air hole is blocked with the remaining fi lm, ink
may leak out or may not eject properly.
b
Twist off and discard the orange
protective cap located on the bottom of
the ink tank.
Electrical Contacts
Ink Port
Protective Cap
Do not press!
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
c
Insert the ink tank into the right-hand
slot and press the mark on the ink
tank until it clicks into place.
d
Make sure the ink lamp lights red.
Refer to the color
guide on the Print
Head Lock Lever.
e
Lift the Scanning Unit (Printer Cover)
slightly to set the Scanning Unit
Support back to its original position,
and then gently close the Scanning Unit
(Printer Cover).
Important
The machine starts the preparatory operation.
It takes about 2 minutes. Do not start another
operation until the machine has stopped making
operating noises.
f
When the message “
Perform head
alignment if colors/lines are
misaligned” is displayed, press the OK
button. The copy standby screen will be
displayed.
Important
When printing for the fi rst or second time after
setup, the print will take a minute or two before it
becomes ready to print.
Note
If lines are misaligned or the print result is not
satisfactory, perform the print head alignment.
Refer to “Aligning the Print Head” in “Routine
Maintenance” of the Quick Start Guide.
If the
Alarm lamp is lit and an error message is
displayed on the LCD, refer to “An Error Message Is
Displayed on the LCD” in “Troubleshooting” of the
Quick Start Guide.
Hardware setup is complete.
•
•
f
Make sure that the Print Head is
installed properly.
OK
Important
• Be sure that the Print Head Lock Lever is
pressed all the way down, and that the Print
Head is locked firmly in place. If the Print Head
is tilted forward, or the Print Head Lock Lever is
pressed only halfway down, raise the Print Head
Lock Lever and remove the Print Head, and then
reinstall the Print Head.
• If the Scanning Unit (Printer Cover) is left open
for more than 10 minutes, the Print Head Holder
moves to the right. Close and reopen the Scan-
ning Unit (Printer Cover) to return the Holder to
the center.