Canon MX700 网络指南
32
“Communication with the Card Slot
failed.” is displayed during the network
setup of the Card Slot
(Continued)
failed.” is displayed during the network
setup of the Card Slot
(Continued)
If the setup is in progress, click Skip to complete the setup. Then mount the
Card Slot using the Canon IJ Network Tool.
z
Card Slot using the Canon IJ Network Tool.
z
Change the workgroup name to “WORKGROUP” following the procedure
below.
(1)Right-click My Computer, then select Properties.
(2)Select the Computer Name tab, then click Change.
(3)Change the workgroup name to “WORKGROUP”, then click OK.
below.
(1)Right-click My Computer, then select Properties.
(2)Select the Computer Name tab, then click Change.
(3)Change the workgroup name to “WORKGROUP”, then click OK.
Important
If you change the firewall or workgroup settings of the computer during the
setup, you may be prompt to restart the computer to enable the settings. In
this case, click Skip to complete the setup without changing any settings.
You can set up the Card Slot in the Maintenance screen of the Canon IJ
Network Tool after changing the necessary settings and restarting the
computer. For details, refer to “Using the Card Slot over a Network” in the
User’s Guide on-screen manual.
setup, you may be prompt to restart the computer to enable the settings. In
this case, click Skip to complete the setup without changing any settings.
You can set up the Card Slot in the Maintenance screen of the Canon IJ
Network Tool after changing the necessary settings and restarting the
computer. For details, refer to “Using the Card Slot over a Network” in the
User’s Guide on-screen manual.
If these do not resolve the problem, click Skip to complete the setup without the
network setup of the Card Slot. To mount the Card Slot as the network drive
after setup, refer to “Troubles in the Network Setup of the Card Slot” in
“Troubleshooting” in the User’s Guide on-screen manual.
network setup of the Card Slot. To mount the Card Slot as the network drive
after setup, refer to “Troubles in the Network Setup of the Card Slot” in
“Troubleshooting” in the User’s Guide on-screen manual.
z
Make sure that a memory card is inserted in the Card Slot. If it is not inserted,
insert it.
insert it.
Note
Depending on the Mac OS version, the authentication screen may appears.
If it appears, click OK.
If it appears, click OK.
If these do not resolve the problem, click Skip to complete the setup without the
network setup of the Card Slot. To mount the Card Slot as the network drive
after setup, refer to “Troubles in the Network Setup of the Card Slot” in
“Troubleshooting” in the User’s Guide on-screen manual.
network setup of the Card Slot. To mount the Card Slot as the network drive
after setup, refer to “Troubles in the Network Setup of the Card Slot” in
“Troubleshooting” in the User’s Guide on-screen manual.
“The Card Slot is already mapped as
Network Drive to this computer.” is
displayed during setup
Network Drive to this computer.” is
displayed during setup
The Card Slot is already available. Click OK to close the dialog, then click Next
on the Network Setup of the Card Slot dialog box.
on the Network Setup of the Card Slot dialog box.
“Cannot map any more drives, because
all the drive letters are assigned.” is
displayed during the network setup of
the Card Slot
all the drive letters are assigned.” is
displayed during the network setup of
the Card Slot
Click Skip to complete the setup. After software installation is complete, remove
any drive letter and try the network setup of the Card Slot again using the
Canon IJ Network Tool. For details, refer to “Using the Card Slot over a
Network” in the User’s Guide on-screen manual.
any drive letter and try the network setup of the Card Slot again using the
Canon IJ Network Tool. For details, refer to “Using the Card Slot over a
Network” in the User’s Guide on-screen manual.
Problem
Possible Cause and Measures
QT5-1386-V01
©CANON INC. 2007
PRINTED IN THAILAND