Samson vx115 用户指南
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers are wired in "Parallel"
the total impedance is cut in half and
when two speakers are wire is “Series”
the total impedance is the sum of the
speakers individual impedance.
the total impedance is cut in half and
when two speakers are wire is “Series”
the total impedance is the sum of the
speakers individual impedance.
The VX115 impedance (many audio
guys used the made up word “ohmage”,
however the correct term is impedance)
is 8 Ohms. So, when two VX115’s are
connected together in parallel, the total
impedance is 4 Ohms. The impedance
of your speaker also has an effect on
your amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
guys used the made up word “ohmage”,
however the correct term is impedance)
is 8 Ohms. So, when two VX115’s are
connected together in parallel, the total
impedance is 4 Ohms. The impedance
of your speaker also has an effect on
your amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
IMPORTANT
: There is a minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
Connecting the VX115 to Your Amplifier
The VX115 connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the VX115’s rear
jackplate.
The VX115 connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the VX115’s rear
jackplate.
Using the EXTENSION Output
The VX115 provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook-up
with your amplifier. Follow the steps
below to connect two VX115’s using the
Extension Output. Connect the
Amplifier Output to the Input of the first
VX115. Now, connect the Extension
Output to the Input of the second
VX115.
The VX115 provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook-up
with your amplifier. Follow the steps
below to connect two VX115’s using the
Extension Output. Connect the
Amplifier Output to the Input of the first
VX115. Now, connect the Extension
Output to the Input of the second
VX115.
Hartke
EXTENSION
INPUTS
MADE IN CHINA
SERIAL NUMBER
Hartke Systems Distributed worldwide by Samson Technologies
www.hartke.com
VX115 BASS CABINET
300 WATTS
-series
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000
200 WATTS
8
= 120 WATTS
4
= 200 WATTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLED IN R.O.K.
SERIAL NUMBER
115
~ AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
SPEAKER OUTPUTS
8
8
ON
OFF
HPF
EFFECT
SEND
RETUIRN
8
Connecting the VX115
Hartke
EXTENSION
INPUTS
MADE IN CHINA
SERIAL NUMBER
-series
Hartke Systems Distributed worldwide by Samson Technologies
www.hartke.com
VX115 BASS CABINET
300 WATTS
8
8
Hartke
EXTENSION
INPUTS
MADE IN CHINA
SERIAL NUMBER
-series
Hartke Systems Distributed worldwide by Samson Technologies
www.hartke.com
VX115 BASS CABINET
300 WATTS
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
Samson Technologies Corp.
Hicksville, New York 11802
MODEL 2000
200 WATTS
8
= 120 WATTS
4
= 200 WATTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
ASSEMBLED IN R.O.K.
SERIAL NUMBER
115
~ AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
SPEAKER OUTPUTS
8
8
ON
OFF
HPF
EFFECT
SEND
RETUIRN